International Journal of Heat and Mass Transfer

International Journal of Heat and Mass Transfer, Vol.128 Entire volume, number list

ISSN: 0017-9310 (Print)

In this Issue (111 articles)

1 - 11	Flow visualization of R32 in parallel-port microchannel tube Li HP, Hrnjak P
12 - 23	Analysis of mechanical-fluid-thermal performance of heat pipeline system with structural deformation effects Xu Q, Feng JX, Liu L, Zhou JZ, Ye GC, Chang C
24 - 45	Effects of magnetic field on thermo-hydraulic performance of Fe3O4-water nanofluids in a corrugated tube Mei SY, Qi C, Luo T, Zhai XF, Yan YY
46 - 53	On the theory of nucleation and nonstationary evolution of a polydisperse ensemble of crystals Alexandrov DV, Nizovtseva IG, Alexandrova IV
54 - 65	Heat transfer and pressure loss characteristics in a swirl cooling tube with dimples on the tube inner surface Liu YY, Rao Y, Weigand B
66 - 75	Heat transfer enhancement in a parallel, finless heat exchanger using a longitudinal vortex generator, Part B: Experimental investigation on the performance of finless and fin-tube heat exchangers Li JY, Dang CB, Hihara E
76 - 86	Transition to a chaotic flow in a V-shaped triangular cavity heated from below Bhowmick S, Saha SC, Qiao MM, Xu F
87 - 97	Heat transfer enhancement in a parallel, finless heat exchanger using a longitudinal vortex generator, Part A: Numerical investigation Li JY, Dang CB, Hihara E
98 - 114	Numerical modeling of in-furnace sulfur removal by sorbent injection during pulverized lignite combustion Tomanovic I, Belosevic S, Crnomarkovic N, Milicevic A, Tucakovic D
115 - 124	Drop evaporation of hydrocarbon fluids with deposit formation Hanichen P, Bender A, Voss B, Gambaryan-Roisman T, Stephan P
125 - 135	Numerical and experimental investigation of heat transfer in a solar receiver with a variable aperture Abuseada M, Ozalp N, Ophoff C
136 - 149	Condensation heat transfer and pressure drop characteristics of R134a, R1234ze(E), R245fa and R1233zd(E) in a plate heat exchanger Zhang J, Kaern MR, Ommen T, Elmegaard B, Haglind F
150 - 160	Graetz problem for combined pressure-driven and electroosmotic flow in microchannels with distributed wall heat flux Azari M, Sadeghi A, Chakraborty S
161 - 170	Experimental and numerical study on the heat transfer downstream of a confined rectangular cylinder in the laminar regime Meis M, Varas F, Arias JR, Velazquez A, Carretero L
171 - 184	CHF correlation development under ERVC conditions by using the local liquid velocity from PIV measurements Yoon J, Kam DH, Park HM, Jeong YH
185 - 198	3D lattice Boltzmann investigation of nucleation sites and dropwise-to-filmwise transition in the presence of a non-condensable gas on a biomimetic surface Guo Q, Cheng P
199 - 207	Determination of thermal conductivity of interfacial layer in nanofluids by equilibrium molecular dynamics simulation Wang X, Jing DW
208 - 216	Theoretical and experimental studies of heat transfer characteristics of a single-phase natural circulation mini-loop with end heat exchangers Cheng HJ, Lei HY, Zeng L, Dai CS
217 - 228	Influence of lubricant-mediated droplet coalescence on frosting delay on lubricant impregnated surfaces Seo D, Oh S, Moon B, Kim H, Kim J, Lee C, Nam Y
229 - 238	Observation of the mechanism triggering critical heat flux in pool boiling of saturated water under atmospheric pressure Jung S, Kim H
239 - 247	Topology optimization of the wick geometry in a flat plate heat pipe Lurie SA, Rabinskiy LN, Solyaev YO
248 - 269	Flow deflectors to release the negative defect of natural wind on large scale dry cooling tower Wu T, Ge ZH, Yang LJ, Du XZ
270 - 278	Investigation of wave interference effect in Si/Ge superlattices with interfering Monte Carlo method Yu JC, Li Q, Ye WJ
279 - 289	Heat transfer of laminar pulsating flow in a rectangular channel Blythman R, Persoons T, Jeffers N, Murray DB
290 - 318	Influence of heating surface characteristics on flow boiling in a copper microchannel: Experimental investigation and assessment of correlations Jayaramu P, Gedupudi S, Das SK
319 - 334	Forced convection heat transfer from a circular cylinder with a flexible fin Sun X, Ye ZH, Li JJ, Wen K, Tian H
335 - 343	Image-based numerical prediction for effective thermal conductivity of heterogeneous materials: A quadtree based scaled boundary finite element method He YQ, Guo J, Yang HT
344 - 353	New model for heat transfer calculation during film condensation inside pipes Camaraza-Medina Y, Hernandez-Guerrero A, Luviano-Ortiz JL, Mortensen-Carlson K, Cruz-Fonticiella OM, Garcia-Morales OF
354 - 362	Developing laminar natural convection of power law fluids in vertical open ended channel Zhou EG, Bayazitoglu Y
363 - 377	Elliptical double corrugated tubes for enhanced heat transfer Navickaite K, Cattani L, Bahl CRH, Engelbrecht K
378 - 391	The normal spectral emission characteristics of Ni-based alloys during oxidation at high temperatures Zhao SN, Li XF, Huai XL, Zhou XM, Cheng KY
392 - 400	Experimental research on the effective heating strategies for a phase change material based power battery module Lv YF, Yang XQ, Zhang GQ, Li XX
401 - 417	Water functionalized CuO nanoparticles filled in a partially heated trapezoidal cavity with inner heated obstacle: FEM approach ul Haq R, Aman S
418 - 430	Experimental study of saturated pool boiling heat transfer with FeCrAl- and Cr-layered vertical tubes under atmospheric pressure Son HH, Cho YS, Kim SJ
431 - 442	Local heat transfer characteristics of natural circulation flow inside an 8 x 8 partial spent fuel assembly under dry storage Shin D, Kwon JS, Kim T, Kim SJ
443 - 449	X-ray imaging analysis on behaviors of boiling bubbles in nanofluids Park H, Lee SJ, Jung SY
450 - 458	Experimental investigations on pressure oscillation induced by steam-air mixture gas sonic jets in subcooled water Li WC, Meng ZM, Wang JJ, Liu JQ, Sun ZN
459 - 468	Numerical analysis of droplet impact and heat transfer on an inclined wet surface Li DS, Duan XL
469 - 478	Heat flux reconstruction by inversion of experimental infrared temperature measurements - Application to the impact of a droplet in the film boiling regime Chaze W, Caballina O, Castanet G, Pierson JF, Lemoine F, Maillet D
479 - 491	Non-Oberbeck-Boussinesq effects due to large temperature differences in a differentially heated square cavity filled with air Wang Q, Xia SN, Yan R, Sun DJ, Wan ZH
492 - 503	Numerical modeling and experimental validation of fractional heat transfer induced by gas adsorption in heterogeneous coal matrix Kang JH, Zhang D, Zhou FB, Li HJ, Xi TQ
504 - 515	Ultra-high heat flux dissipation with Piranha Pin Fins Woodcock C, Ng'oma C, Sweet M, Wang YY, Peles Y, Plawsky J
516 - 525	Analytical solutions and numerical simulations of radiative property in the two-layer concentrically spherical large particle Zhu KY, Li SL, Huang Y
526 - 535	Optimization of influence factors for water cooling of high temperature plate by accelerated control cooling process Lim HS, Kang YT
536 - 549	A lattice Boltzmann model for multi-component two-phase gas-liquid flow with realistic fluid properties Deng H, Jiao K, Hou YZ, Park JW, Du Q
550 - 561	Electrostatic-induced coalescing-jumping droplets on nanostructured superhydrophobic surfaces Traipattanakul B, Tso CY, Chao CYH
562 - 569	Component level modelling of heat transfer during vapour phase soldering with finite difference ADI approach Bozsoki I, Geczy A, Illes B
570 - 580	Performance of pool boiling with 3D grid structure manufactured by selective laser melting technique Zhang C, Zhang L, Xu H, Li P, Qian B
581 - 600	Efficient uncertainty quantification of stochastic heat transfer problems by combination of proper orthogonal decomposition and sparse polynomial chaos expansion Mohammadi A, Raisee M
601 - 612	A decoupling penalty finite element method for the stationary incompressible MagnetoHydroDynamics equation Deng JE, Si ZY
613 - 622	Carbon/carbon high thickness shell for advanced space vehicles Albano M, Alifanov OM, Budnik SA, Morzhukhina AV, Nenarokomov AV, Titov DM, Gabrielli A, Ianelli S, Marchetti M
623 - 633	Experimental evaluation of transient heat and mass transfer during regeneration in multilayer fixed-bed binder-free desiccant dehumidifier Shamim JA, Paul S, Kitaoka K, Hsu WL, Daiguji H
634 - 648	Thermohydraulic performance of microchannel heat sinks with triangular ribs on sidewalls - Part 2: Average fluid flow and heat transfer characteristics Chai L, Wang L, Bai X
649 - 667	Two-phase frictional pressure drop in a thin mixed-wettability microchannel Lewis JM, Wang Y
668 - 678	Optical properties and transmittances of ZnO-containing nanofluids in spectral splitting photovoltaic/thermal systems Liang HX, Wang FQ, Li D, Zhu J, Tan JY
679 - 687	A new modelling method for superalloy heating in resistance furnace using FLUENT Fu ZL, Yu XH, Shang HL, Wang ZZ, Zhang ZY
688 - 699	Effects of temperature-dependent properties on natural convection of power-law nanofluids in rectangular cavities with sinusoidal temperature distribution Wang L, Huang CS, Yang XG, Chai ZH, Shi BC
700 - 714	Gravity effects on subcooled flow boiling heat transfer Lebon MT, Hammer CF, Kim J
715 - 727	Air-side heat transfer enhancement in plate-fin channel with an airfoil-based self-agitator Li KJ, Xu XC, Li Z, Chen HH, Chen YY, Wang S, Ke ZQ, Huang GL, Chen CL, Chen CH
728 - 738	Experimental research on condensation of R134a and R404A refrigerants in mini-channels during impulsive instabilities. Part I Kuczynski W
739 - 747	Research on the three-dimensional wall temperature distribution and low-temperature corrosion of quad-sectional air preheater in larger power plant boilers Zhang QN, Sun FZ, Chen CX
748 - 761	An experimental study on the effects of frosting conditions on frost distribution and growth on finned tube heat exchangers Zhang L, Jiang YQ, Dong JK, Yao Y, Deng SM
762 - 772	Effects of magnetic field on the pool boiling heat transfer of water-based alpha-Fe2O3 and gamma-Fe2O3 nanofluids Li SY, Ji WT, Zhao CY, Zhang H, Tao WQ
773 - 782	Experimental research on condensation of R134a and R404A refrigerants in tubular mini-channels during impulsive instabilities. Part II Kuczynski W
783 - 793	Experimental investigation of condensation heat transfer and pressure drop of R-134a flowing inside dimpled tubes with different dimpled depths Aroonrat K, Wongwises S
794 - 806	Investigation on optimization of the thermal performance for compressible laminar natural convection flow in open-ended vertical channel Talukdar D, Li CG, Tsubokura M
807 - 816	Phonon backscatter, trapping, and misalignment effects on microscale thermal conductance below the Casimir limit VanGessel FG, Chung PW
817 - 824	Validation of numerical models for cryogenic-liquid pool spreading and vaporization on solid ground Nguyen LD, Kim M, Choi B, Chung K
825 - 835	Sensitivity analysis and application of machine learning methods to predict the heat transfer performance of CNT/water nanofluid flows through coils Baghban A, Kahani M, Nazari MA, Ahmadi MH, Yan WM
836 - 848	Ice formation modes during flow freezing in a small cylindrical channel Jain A, Miglani A, Huang YH, Weibel JA, Garimella SV
849 - 859	An analytical technique for the optimal designs of tube-in-tank thermal energy storage systems using PCM Fang YH, Niu JL, Deng SM
860 - 864	Influence factors of the evaporation rate of a solar steam generation system: A numerical study Zhong JX, Huang CL, Wu DX, Lin ZZ
865 - 874	A new algorithm for solving an inverse transient heat conduction problem by dividing a complex domain into parts Duda P, Konieczny M
875 - 884	Numerical investigation on heat transfer of the supercritical fluid upward in vertical tube with constant wall temperature Yang Z, Cheng X, Zheng XH, Chen HS
885 - 891	An analysis of the droplet support fiber effect on the evaporation process Chauveau C, Birouk M, Halter F, Gokalp I
892 - 933	Review of pool boiling enhancement by surface modification Liang GT, Mudawar I
934 - 953	Flow patterns of vertically upward and downward air-water two-phase flow in a narrow rectangular channel Chalgeri VS, Jeong JH
954 - 963	The effect of fin oscillation in heat transfer enhancement in separated flow over a backward facing step Kumar S, Vengadesan S
964 - 975	Parameterising continuum models of heat transfer in heterogeneous living skin using experimental data McInerney S, Carr EJ, Simpson MJ
976 - 979	Comments on "'Combined effects of magnetohydrodynamic and temperature dependent viscosity on peristaltic flow of Jeffrey nanofluid through a porous medium: Application to oil refinement' by WM Hasona, AA El-Shekhipy and MG Ibrahim, International Journal of Heat and Mass Transfer, 2018, 126: 700-714" Elogail MA
980 - 990	Optimized inlet geometry of a laidback fan-shaped film cooling hole - Experimental study of film cooling performance Fraas M, Glasenapp T, Schulz A, Bauer HJ
991 - 998	Simulation on falling film absorption based on lattice Boltzmann method at moderate Reynolds number Shi YQ, Chen GM, Wang Q, Chen Q
999 - 1016	Cascaded lattice Boltzmann method based on central moments for axisymmetric thermal flows including swirling effects Hajabdollahi F, Premnath KN, Welch SWJ
1017 - 1025	Passive production of synthesis gas from liquid methanol using a packed bed of porous material particles Okuyama K, Ichimi K, Takazawa M, Natori A, Tanaka M
1026 - 1032	Mathematical modelling of frequency and force impacts on averaged metal flows in alternating magnetic field Nikulin IL, Perminov AV
1033 - 1047	Local end-wall heat transfer enhancement by jet impingement on a short pin-fin Schekman S, Atkins MD, Kim T
1048 - 1063	Spatio-temporal identification of heat flux density using reduced models. Application to a brake pad Carmona S, Rouizi Y, Quemener O
1064 - 1071	Mass transfer characteristics of CO2 absorption into 1-butyl-3-methylimidazolium tetrafluoroborate aqueous solution in microchannel Chu CY, Zhang FB, Zhu CY, Fu TT, Ma YG
1072 - 1080	Effect of evaporator tilt on a loop heat pipe with non-condensable gas Wang HF, Lin GP, Shen XB, Bai LZ, Wen DS
1081 - 1094	Flow boiling heat transfer in mini channel with serrated fins: Experimental investigation and development of new correlation Wen T, Zhan HB, Zhang DL
1095 - 1101	Identification of nucleate boiling as the dominant heat transfer mechanism during confined two-phase jet impingement Clark MD, Weibel JA, Garimella SV
1102 - 1113	Modelling sorption equilibria and kinetics in numerical simulations of dynamic sorption experiments in packed beds of salt/zeolite composites for thermochemical energy storage Lehmann C, Kolditz O, Nagel T
1114 - 1124	Effective and uniform cooling on a porous micro-structured surface with visualization of liquid/vapor interface Noh H, Yoo J, Kim JO, Park HS, Hwang DK, Kim DP, Kim MH
1125 - 1135	Dynamic evolution of the CO2-brine interfacial area during brine imbibition in porous media Jiang LL, Wu BH, Liu Y, Suekane T, Wang DY
1136 - 1148	Physical absorption of CO2 and H2S from synthetic biogas at elevated pressures using hollow fiber membrane contactors: The effects of Henry's constants and gas diffusivities Tantikhajorngosol P, Laosiripojana N, Jiraratananon R, Assabumrungrat S
1149 - 1156	A fractal model of effective thermal conductivity for porous media with various liquid saturation Qin X, Cai JC, Xu P, Dai S, Gan Q
1157 - 1167	Some features of solving an inverse problem on identification of material properties of functionally graded pyroelectrics Vatulyan A, Nesterov S, Nedin R
1168 - 1174	Study on the characteristics of GDL with different PTFE content and its effect on the performance of PEMFC Chen T, Liu SH, Zhang JW, Tang MN
1175 - 1183	Nucleate boiling heat transfer model based on fractal distribution of bubble sizes Qi BJ, Wang Y, Wei JJ, Zhang YH, Yu T
1184 - 1200	Impact of an oscillating guide vane on the thermo-hydraulic fields in a square cavity with single inlet and outlet ports Shih YC, Khodadadi JM, Nien SW, Zeng Y, Huang XL
1201 - 1205	Thin reaction zones in highly turbulent medium Sabelnikov VA, Yu R, Lipatnikov AN
1206 - 1217	Experimental investigation on the Leidenfrost phenomenon of droplet impact on heated silicon carbide surfaces Wang ZF, Xiong JB, Yao WY, Qu WH, Yang YH
1218 - 1228	Numerical simulation of enhancing shale gas recovery using electrical resistance heating method Wang YD, Liao B, Qiu L, Wang DS, Xue QZ
1229 - 1244	Cell transport and suspension in high conductivity electrothermal flow with negative dielectrophoresis by immersed boundary-lattice Boltzmann method Ren QL, Meng FL, Chan CL
1245 - 1262	A finite particle method with particle shifting technique for modeling particulate flows with thermal convection Zhang ZL, Walayat K, Huang C, Chang JZ, Liu MB
1263 - 1279	Contact line dynamics of two-dimensional evaporating drops on heated surfaces with temperature-dependent wettabilities Ye XM, Zhang XS, Li ML, Li CX, Dong S
1280 - 1295	Analytical solutions of fluid flow and heat transfer in a partial porous channel with stress jump and continuity interface conditions using LTNE model Li Q, Hu PF
1296 - 1306	Modeling Leidenfrost drops over heated liquid substrates Qiao L, Zeng Z, Xie HQ, Liu H, Zhang LQ
1307 - 1321	Advective-diffusive-reactive solute transport due to non-Newtonian fluid flows in a fracture surrounded by a tight porous medium Dejam M
1322 - 1343	A thermal non-equilibrium approach on thermo-solutal natural convection due to the lateral flux of heat and solute on enclosure walls: Multi-solutions and oscillations Bera P, Pippal S, Khan A
1344 - 1350	Reexamination of Murray's law for tree-like rectangular microchannel network with constant channel height Jing DL, Song SY, He L