| 3567 - 3575 |
An investigation of the fatigue and fracture behavior of multicomponent Nb-11Al-41Ti-1.5Mo-1.5Cr intermetallic
Soboyejo WO, Ye F, Dipasquale J, Pine P |
| 3577 - 3580 |
Characterization of the spinel phase in a diphasic mullite gel using dynamic X-ray diffraction
Wang Y, Thomson WJ |
| 3581 - 3585 |
Growth of carbon micro-coils by pre-pyrolysis of propane
Chen XQ, Motojima S |
| 3587 - 3590 |
SiO2 entrapment of animal cells - Part I - mechanical features of sol-gel SiO2 coatings
Sglavo VM, Carturan G, Dal Monte R, Muraca M |
| 3591 - 3596 |
Effect of ultrasonic treatment on ripening of titanium oxalate salt from solution
Choi HL, Park C |
| 3597 - 3604 |
Influence of Y2O3 distribution on the rate of tetragonal to monoclinic phase transformation of yttria-stabilized zirconia during hydrothermal aging
Yasuda K, Arai S, Itoh M, Wada K |
| 3605 - 3608 |
Synthesis of aluminum nitride fibres from aluminum silicate fibres by carbothermal reduction method
Fu RL, Zhou HP, Chen L, Wu Y |
| 3609 - 3622 |
Mechano-chemical wear of ceramics
Stolarski TA |
| 3623 - 3630 |
Effect of environmental factors on thermal shock behaviour of polycrystalline alumina ceramics
Hahn BS, Lee HL |
| 3631 - 3638 |
Iron-doped zircon: the mechanism of formation
Berry FJ, Eadon D, Holloway J, Smart LE |
| 3639 - 3646 |
A metallurgical study of the contamination zone at the surface of dental Ti castings, due to the phosphate-bonded investment material: the protection efficacy of a ceramic coating
Papadopoulos T, Zinelis S, Vardavoulias M |
| 3647 - 3652 |
Effective Young's moduli of quasilayered bars using bar resonance frequencies
Kupkova M, Dudrova E, Kabatova M, Kupka M, Danninger H, Weiss B, Melisova D |
| 3653 - 3658 |
Phase decomposition in extruded Zn-Al based alloy
Zhu YH, Hernandez RM, Banos L |
| 3659 - 3667 |
Experimental and theoretical study on the piezoelectric behavior of barium doped PZT
Nasar RS, Cerqueira M, Longo E, Leite ER, Varela AJ, Beltran A, Andres J |
| 3669 - 3676 |
Neutron diffraction study on the medium and short-range order of ternary chalcogenide glasses
Neov S, Gerasimova I, Skordeva E, Arsova D, Pamukchieva V, Mikula P, Lukas P, Sonntag R |
| 3677 - 3684 |
On the disappearance of Mo2C during low-temperature sintering of Ti(C,N)-Mo2C-Ni cermets
Qian M, Lim LC |
| 3685 - 3693 |
Grinding effects of host crystals on formation and properties of titania pillared fluorine micas
Yamaguchi T, Kuniyoshi F, Kitajima K |
| 3695 - 3707 |
Simulation of craze failure in a glassy polymer: rate dependent drawing and rate dependent failure models
Sha Y, Hui CY, Kramer EJ |
| 3709 - 3719 |
Interfacial and mechanical properties of environment-friendly "green" composites made from pineapple fibers and poly(hydroxybutyrate-co-valerate) resin
Luo S, Netravali AN |
| 3721 - 3729 |
Preparation, characterization and photoelectrochemical behaviors of Fe(III)-doped TiO2 nanoparticles
Wang YQ, Cheng HM, Hao YZ, Ma JM, Li WH, Cai SM |
| 3731 - 3735 |
Fabrication of laminated metal-intermetallic composites by interlayer in-situ reaction
Xia ZH, Liu JH, Zhu SQ, Zhao YZ |
| 3737 - 3745 |
Characterization of bitumens modified with SEBS, EVA and EBA polymers
Isacsson U, Lu XH |
| 3747 - 3753 |
Undercooling, liquid separation and solidification of Cu-Co alloys
Robinson MB, Li D, Rathz TJ, Williams G |
| 3755 - 3767 |
Melt processing and microstructural analysis of GdBa(2)Cu(3)Oy with varying amounts of Gd2BaCuO5 phase
Reddy ES, Rajasekharan T |
| 3769 - 3778 |
Pressure induced amorphization in calcium phosphates
Vaidya SN, Sugandhi V |
| 3779 - 3787 |
Amorphous chalcogenide Se1-x-yTexPy semiconducting alloys: thermal and mechanical properties
Kasap SO, Wagner T, Aiyah V, Krylouk O, Bekirov A, Tichy L |
| 3789 - 3793 |
Effect of pure-solvents without deflocculants for finer SiC particle dispersed MgO based composite
Choa YH, Bamba N, Hayashi H, Kondo H, Sekino T, Niihara K |
| 3795 - 3800 |
Effect of ZrO2 and SiO2 on glass forming ability of Zr57Cu20Al10Ni8Ti5 alloy
Xing LQ, Herlach DM |
| 3801 - 3812 |
Solid state sintering of ceramics: pore microstructure models, densification equations and applications
Shi JL |
| 3813 - 3819 |
Fabrication of gradient distribution alumina short fibre reinforced aluminium alloy
Ma AB, Imura T, Kuzuya K, Nishida Y |
| 3821 - 3829 |
Determination of surface heterogeneity by contact angle measurements on glassfibres coated with different sizings
Wolff V, Perwuelz A, El Achari A, Caze C, Carlier E |
