| 215 - 227 |
Creep of CaO/SiO2-containing MgO refractories
Wereszczak AA, Kirkland TP, Curtis WF |
| 229 - 233 |
Tensile properties of VGCF reinforced carbon composites
Ting JM |
| 235 - 239 |
In-situ high temperature X-ray diffraction study of Ni/SiC interface reactions
Fujimura T, Tanaka SI |
| 241 - 246 |
Fracture of Gd-2 (MoO4)(3) single crystals
Panfilov P, Gagarin YL, Shur VY |
| 247 - 250 |
Effect of humidity on crack healing in glass from in-situ investigations using an ESEM
Wilson BA, Case ED |
| 251 - 256 |
Structure and properties of new perovskites La2MRhO6 (M = Mg, Zn)
Schinzer C, Demazeau G |
| 257 - 265 |
Mechanically alloyed Ni/8YSZ powder mixtures: preparation, powder characterization and sintering behavior
Wilkenhoener R, Vassen R, Buchkremer HP, Stover D |
| 267 - 271 |
Annealing characteristics of Si doped amorphous silica films by rf sputtering
Yoshida S, Hanada T, Tanabe S, Soga N |
| 273 - 276 |
A comparative study of silver-epoxy and tin-lead solder in their joints with copper, through mechanical and electrical measurements during debonding
Luo X, Chung DDL |
| 277 - 281 |
Effect of rolling temperature on interface and bond strength development of roll bonded copper/aluminium metal laminates
Peng XK, Heness G, Yeung WY |
| 283 - 290 |
Development of a methodology for assessing the integrity of dental restorations
D'Arcy SP, Gorman DG, Saunders WP, Taylor RM |
| 291 - 299 |
The mechanical behavior of foamed aluminum
Fusheng H, Zhengang Z |
| 301 - 305 |
Molten salt synthesis of single-phase BaNd2Ti4O12 powder
Katayama K, Azuma Y, Takahashi Y |
| 307 - 322 |
Formation of titanium carbonitride phases via the reduction of TiO2 with carbon in the presence of nitrogen
Jha A, Yoon SJ |
| 323 - 327 |
Electrical properties of some (1,1,1) intermetallic compounds
Cook BA, Harringa JL |
| 329 - 336 |
Effect of elastic interaction energy on coarsening of gamma ＇ precipitates in a mechanically alloyed ODS Ni-base superalloy
Ryu HJ, Hong SH, Weber J, Tundermann JH |
| 337 - 347 |
Preparation, characterization, and optical properties of disulfide-comprising oligo[2,5-bis(thiomethyl)-1,4-dithiane] and its poly[S-alkylcarbamate]
Okubo T, Kohmoto S, Yamamoto M, Nakahira T |
| 349 - 353 |
A versatile plasma technique to improve plastic materials against gas and water-vapour permeation
Moser EM, Muller C |
| 355 - 358 |
Kinetics of nucleation and halt-in-growth processes in a thin layer
Tagami T, Tanaka SI |
| 359 - 364 |
Brass-matrix silicon carbide whisker composites prepared by powder metallurgy
Yih P, Chung DDL |
| 365 - 369 |
Sequential electron beam evaporation of YBCO thin films through the barium fluoride route
Moorthy VHS, Tomar VS |
| 371 - 377 |
Growth of Bi12GeO20 crystal rods and fibers by the improved floating zone method
Fu S, Ozoe H |
| 379 - 384 |
Change of mechanical properties of rigid poly(vinylchloride) during photochemical ageing
Anton-Prinet C, Mur G, Gay M, Audouin L, Verdu J |
| 385 - 394 |
Glass-fiber reinforcement of in situ compatibilized polypropylene/polyethylene blends
Tselios C, Bikiaris D, Savidis P, Panayiotou C, Larena A |
| 395 - 406 |
Low velocity response of simple geometry pultruded glass/polyester composite
Wisheart M, Richardson MOW |
| 407 - 416 |
Microstructural development in cast and aged Ni-Al-Cr-based alloys derived from the B2 type beta-NiAl structure
Gale WF, Abdo ZAM, Nemani RV |
| 417 - 422 |
The mechanical properties of elastomers in high-pressure CO2
Davies OM, Arnold JC, Sulley S |
