| 655 - 666 |
Atomistic simulation of grain boundary sliding and migration
Chandra N, Dang P |
| 667 - 673 |
Weibull master curves and fracture toughness testing - Part I -Master curves for quasi-static uniaxial tensile and bend tests
Lambrigger M |
| 675 - 681 |
Weibull master curves and fracture toughness testing - Part II - Evaluation of data of quasi-static three-point bend tests of tetragonal zirconia, zirconia/alumina and silicon nitride
Lambrigger M |
| 683 - 690 |
An AFM-SEM investigation of the effect of silica fume and fly ash on cement paste microstructure
Papadakis VG, Pedersen EJ, Lindgreen H |
| 691 - 700 |
Influence of calcination and sintering temperatures on the structure of (Pb1-xBax)ZrO3
Pokharel BP, Datta MK, Pandey D |
| 701 - 706 |
Microstructural evolution during combustion reaction between CuO and Al induced by high energy ball milling
Zhang DL, Richmond JJ |
| 707 - 709 |
BaTiO3 thin film prepared by coating-pyrolysis process on Nb-doped SrTiO3 substrate
Kim S, Kwon OY |
| 711 - 717 |
The effect of hydrogen on the bainite transformation
Yalci HK, Edmonds DV |
| 719 - 725 |
Fatigue performance of a cast aluminium alloy Al-7Si-Mg with surface defects
Jiang H, Bowen P, Knott JF |
| 727 - 733 |
Nebulized spray deposition of PLT thin film
Huang CS, Chen JS, Lee CH |
| 735 - 747 |
Structure and properties of rapidly solidified Al rich Al-Mn-Si alloys - Part I - Melt spun ribbons
Wilkes DMJ, Jones H |
| 749 - 761 |
Structure and properties of rapidly-solidified Al-rich Al-Mn-Si alloys - Part II - Atomized powder, its extrudate and the effect of blended-in SiC
Wilkes DMJ, Jones H |
| 763 - 767 |
A mathematical model for carbothermic nitridation of carbon metal oxide pellet - Effect of pressure gradient
Chen HK, Lin CI |
| 769 - 772 |
Effect of heating rate on grain morphology of in situ reinforced reaction bonded aluminium niobate-based composites
Garcia DE, Janssen R, Claussen N, Brito WE |
| 773 - 781 |
Kinetics of discontinuous precipitation and type I discontinuous coarsening in Zn-4 at % Ag alloy
Manna I, Jha JN, Pabi SK |
| 783 - 794 |
Computer simulation of grain growth by grain boundary migration during liquid phase sintering
Nikolic ZS |
| 795 - 799 |
Distribution of the crystal modifications in polymorphous PbSe films revealed by microhardness measurements
Baleva M, Mateeva E, Trifonova EP |
| 801 - 809 |
"Mimetic" molecular composites of Kevlar (R) aramid/poly(p-phenyleneterephthalamide)
Memeger W |
| 811 - 820 |
A study of high-temperature precipitation in Al-Mg-Si alloys with an excess of silicon
Eskin DG, Massardier V, Merle P |
| 821 - 826 |
The rate-controlling mechanism(s) during plastic deformation of polycrystalline NaCl at 0.28-0.75 T-M
Conrad H, Yang D |
| 827 - 834 |
The properties of carbon fibre SiC composites fabricated through impregnation and pyrolysis of polycarbosilane
Zheng GB, Sano H, Uchiyama Y, Kobayashi K, Cheng HM |
| 835 - 842 |
Production of Si3N4 by carbothermal reduction and nitridation of sepiolite
Arik H, Saritas S, Gunduz M |
| 843 - 849 |
Strength changes of moulded polyamide composite caused by thermal oxidation
Kohout J |
| 851 - 857 |
Pitting corrosion inhibition of 316 stainless steel in phosphoric acid chloride solutions Part I - Potentiodynamic and potentiostatic polarization studies
El Dahan HA |
| 859 - 868 |
Pitting corrosion inhibition of 316 stainless steel in phosphoric acid chloride solutions Part II - AES investigation
El Dahan HA |
| 869 - 874 |
Electrocatalytic activity and anodic stability of electrodeposited ruthenium-rhodium coatings on titanium
Vukovic M, Marijan D, Cukman D, Pervan P, Milun M |
| 875 - 880 |
Tribological behavior and wear surface analysis of metal-matrix composites
Sahin Y |
| 881 - 886 |
Structure of zinc-nickel alloyelectrodeposits
Bruet-Hotellaz, Bonino JP, Rousset A, Marolleau, Chauveau E |
| 887 - 890 |
Growth and optical properties of CdSxSe1-x nanocrystals embedded in a novel phosphate glass
Lipovskii AA, Kolobkova EV, Petrikov VD |
