| 1055 - 1057 |
Thermoelectric properties of pressureless-sintered PbSe ceramics
Unuma H, Shigetsuka N, Takahashi M, Masui K |
| 1059 - 1061 |
Phase transformations induced in magnetite by high energy ball milling
Sorescu M |
| 1063 - 1065 |
Second harmonic generation in BaTiO3 film crystallized on tellurite glass surface
Tanaka K, Kuroda H, Narazaki A, Hirao K, Soga N |
| 1067 - 1069 |
On crack tip observation in ionic crystals upon unloading
Yu CC, Lee S |
| 1071 - 1075 |
Oscillation of potential and current during the initiation of crevice corrosion on carbon steel
Yang MZ, Luo JL, Wilmott M |
| 1077 - 1079 |
Hydroxyapatite/metal composite coatings prepared by multi-step electrodeposition method
Zhang JM, Lin CJ, Feng ZD, Tian ZW |
| 1081 - 1084 |
Microstructure and fracture toughness of in-situ toughened SiC-TiC composites
Cho KS, Choi HJ, Lee JG, Kim YW |
| 1085 - 1088 |
Surface topography of retrieved PCA acetabular liners: proposal of a novel wear mechanism
Elfick AP, Hall RM, Unsworth A, Pinder IM |
| 1089 - 1093 |
Oxidation resistance of ODS alloy PM2000 from 880 degrees C to 1400 degrees C
Lours P, Alexis J, Bernhart G |
| 1095 - 1097 |
Measurements of dynamic elastic modulus, vibration damping, and other physical properties of the Zr57Ti5Al10Cu20Ni8 amorphous alloy in the amorphous and crystalline states
Wolfenden A, Barrios KA, Xing LQ |
| 1099 - 1102 |
Preparation and characterization of new glasses from the TeO2-CdO-Al2O3-SiO2 system
Zayas ME, Espinoza-Beltran FJ, Romero M, Rincon JM |
| 1103 - 1106 |
The influence of loading rate on the mixed-mode interlaminar fracture properties of carbon fiber reinforced PEEK
Cantwell WJ, Blyton M, Sixsmith P, Hiley M |
| 1107 - 1109 |
Effect of multi-point indentation on the bending strength of silicon nitride ceramic
Gong JH, Zhang K, Liu S |
| 1111 - 1112 |
Some notes on sliding friction and testing adhesion and bonding of fibers
Andersson CH |
| 1113 - 1115 |
Chemical reactions between vanadium oxides and carbon during high energy ball milling
Zhang DL, Zhang YJ |
| 1117 - 1119 |
High-energy Ni implantation in InP
Chini TK, Bhattacharyya SR, Basu D, Rout B, Ghose S, Sundaravel B, Dev BN, Okuyama F, Kaneko M |
| 1121 - 1123 |
Sliding wear response of an Al-Cu alloy: the influence of SiC particle reinforcement and test parameters
Prasad BK, Venkateswarlu K, Jha AK, Modi OP, Das S, Dasgupta R, Yegneswaran AH |
| 1125 - 1127 |
Nanocrystallization kinetics of Fe85.5Zr4Nb4B5.5Al1 amorphous alloy
Al-Haj M, Barry J |
| 1129 - 1131 |
Properties of light-emitting diode fabricated through stabilization of Li acceptors
Krasnov AN |
| 1133 - 1135 |
PTCR effect in composite conducting polymer films
Hirano S, Kishimoto A, Miyayama M |
| 1137 - 1140 |
Mechanodynamic relaxations in low ethylene content ethylene-vinyl acetate copolymers and in their hydrolyzed products
Fonseca C |
| 1141 - 1143 |
Drops in the flow stress of semi-crystalline polymers at very high rates of strain
Al-Maliky N, Fernandez JO, Parry DJ, Swallowe GM |
| 1145 - 1147 |
Epitaxial growth of PbTe film on Si substrate
Sahay SS, Guruswamy S |
| 1149 - 1151 |
Fabrication and properties of transparent glass-ceramics in Na2O-Nb2O5-TeO2 system
Kim HG, Komatsu T |
