| 1921 - 1923 |
Electrochemical synthesis of crystalline and amorphous manganese coatings
Gong J, Zana I, Zangari G |
| 1925 - 1928 |
A simple approach to enhance the deposition of polyaniline films with self-assembled polyelectrolyte layers
Li D, Ding WY, Wang X, Lu LD, Yang XJ |
| 1929 - 1931 |
Solvent removal from solution-cast films of biodegradable polymers
Freier T, Kunze C, Schmitz KP |
| 1933 - 1935 |
Electrical properties of vacuum-evaporated CdTe thin films
Sahay PP, Jha S, Shamsuddin M |
| 1937 - 1940 |
Microstructure of the interface of a solid state diffusion bond between Inconel alloy 718 and 17-4 PH stainless steel
Zhang GG, Chandel RS, Seow HP, Hoon HH |
| 1941 - 1942 |
Muscle cell adhesion on polytetrafluorethylene modified by UV irradiation
Svorcik V, Walachova K, Heitz J, Gumpenberger T, Bacakova L |
| 1943 - 1945 |
Effect of the particle size of PZT on the microstructure and the piezoelectric properties of 0-3 PZT/polymer composites
Rujijanagul G, Boonyakul S, Tunkasiri T |
| 1947 - 1951 |
Dynamic recrystallization and dynamic recovery of 99.99 mass% aluminum single crystal having [112] orientation
Yamagata H, Ohuchida Y, Saito N, Otsuka M |
| 1953 - 1955 |
Correlation between shear modulus and porosity in porous materials
Kovacik J |
| 1957 - 1959 |
Influence of external stress on the in vitro degradation behavior of C3D/PLA composites
Wan YZ, Wang YL, Zheng LY, Zhou FG, Zhao Q, Cheng GX |
| 1961 - 1963 |
A new crystalline phase (Na2O center dot 8TeO(2)) in the Na2O-TeO2 system
Zhu DM, Zhou WC, Ray CS |
| 1965 - 1967 |
Surface characteristic change of SiC reinforced Mg-alloy composite induced by excimer laser surface treating
Wang AH, Yue TM |
| 1969 - 1970 |
Synthesis of fine nickel powders by glycothermal process
Bae DS, Kim WH, Kim SW, Han KS, Adair JH |
| 1971 - 1973 |
Preparation of Ti3AlC2 and Ti2AlC by self-propagating high-temperature synthesis
Zhou AG, Wang CA, Ge ZB, Wu LF |
| 1975 - 1977 |
Processing of roughened silica film by coagulated colloidal silica for super-hydrophobic coating
Nakajima A, Saiki C, Hashimoto K, Watanabe T |
| 1979 - 1982 |
Possibilities for hot deformation reaction synthesis as a processing route for manufacturing nickel aluminide (Ni3Al) from elemental powders
Minay EJ, Sutthisripok W, Rawlings RD, McShane HB |
| 1983 - 1985 |
Preparation and dielectric properties of sol-gel routed resorcinol formaldehyde (RF) polymer film
Williams RV, Pitchumani S, Subramanian N |
| 1987 - 1988 |
Synthesis of GaN nanotubes
Li JY, Chen XL, Qiao ZY, Cao YG, Li H |
| 1989 - 1991 |
Behavior of internal mold release agent during BMC thermosets composites cure and aging
Serre C, Vayer M, Erre R |
| 1993 - 1994 |
The activation behavior of rapidly solidified Ni-Zr-Al amorphous alloy for the catalytic application
Zhang GS, Sun YF, Shen NF |
| 1995 - 1997 |
Macroparticle induced corrosion for arc bond sputtering CrN/NbN superlattice coatings
Wang HW, Stack MM, Hovsepian P, Munz WD |
| 1999 - 2001 |
Stress analysis of differently oriented crack tip in fully lamellar TiAl based alloys
Lu YH, Wang JP, Zhang YG |
| 2003 - 2004 |
The transmission loss of nano-crystal and polymer composite thin film PT/PEK-c
Yang XD, Ren Q, Lu ZH, Meng FQ, Li YF, Ma CB, Xu D |
