| 193 - 195 |
Preparation of Al2O3-AlON and Al2O3-AlN composites via reaction-bonding
Cai KF, Mclachlan DS, Sigalas I |
| 197 - 199 |
Fitting corrosion of an Al-Mg-Si-Cu alloy reinforced with nitride particles, P/M processed
Ortiz JL, Caprio JJ, Amigo V, Salvador MD |
| 201 - 203 |
Development of synergistic AlN ceramics by simultaneous addition of BN and TiN
Tajika M, Matsubara H, Rafaniello W, Hojo J |
| 205 - 207 |
Preparation of porous ceramic pellet by pseudo double-emulsion method from 4-phase foamed slurry
Lee JS, Park JK |
| 209 - 211 |
The effect of the grain size on the oxidation resistance of Nd-Fe-B magnets
Saito T |
| 213 - 214 |
Observations of surface radial cracks on ceramic bend test fracture surfaces
D'ouza CM |
| 215 - 217 |
Crystallization and sintering of cordierite and anorthite based binary ceramics
Boudchicha MR, Achour S, Harabi A |
| 219 - 221 |
Growth and characterization od SnOx : F thin films prepared by pyrolysis of SnCl2
De la Garza-Guadarrama V, Sanchez-Juarez A, Tiburcio-Silver A, Ortiz A |
| 223 - 226 |
Infiltration of alumina sol into SLS processed porous Al2O3-Al4B2O9 ceramic composites
Lee I |
| 227 - 228 |
Growth of tin nitride thin films by atmospheric pressure chemical vapor deposition using a halide source
Takahashi N, Terada K, Nakamura T |
| 229 - 232 |
Sagging resistance of cold rolled aluminum 4343/3N03/4343 clad sheet
Yoon JS, Lee SH, Kim MS |
| 233 - 235 |
Fabrication of polyaniline/phthalocyanine hybrid ultrathin films via electrostatic attraction and doping reaction
Li D, Jiang YD, Li YR, Yang XJ, Lu LD, Wang X |
| 237 - 239 |
The electronic states of Ba1-xCaxTiO3 and BaTi1-yCayO3 crystalline ceramics
Chang MC, Sugihara S |
| 241 - 244 |
Vertical Bridgman growth of InSb1-xBx crystals for LWIR applications
Mohan P, Babu SM, Santhanaraghavan P, Ramasamy P |
| 245 - 247 |
Gettering phenomenon of oxidation-induced stacking-faults in silicon-on-insulator structure by water-direct-bonding method
Kim KT, Choi DJ |
| 249 - 251 |
Improvement of the surface stability of indium-doped Hg0.8Cd0.2Te epitaxial layers grown on p-Cd0.96Zn0.04Te substrates by photochemical passivation
Jeon HC, Kang TW, Kim TW |
| 253 - 256 |
Influence of Cr2O3 on the sintering, microstructure and mechanical performances of ZTM-Al2O3
Jin HX, Gao L, Chen YR, Yuan QM |
| 257 - 258 |
Comments on "A new Raman peak in a high-density polyethylene"
Bernabe-Rodriguez A, Young RJ |
| 259 - 260 |
Solid solubility of carbon in copper mechanically alloyed
Yamane T, Okubo H, Hisayuki K, Oki N, Konishi M, Komatsu M, Minamino Y, Koizumi Y, Kiritani M, Kim SJ |
| 261 - 263 |
Preparation and mechanical properties of unidirectional Hi-nicalon fiber reinforced silicon carbide composites
Zhou XG, Zhang CR, Ma J, He XB, Cao YB |
| 265 - 267 |
The effect of the substrate material on the value of the adhesive fracture energy, G(c): Further considerations
Blackman BRK, Kinloch AJ, Paraschi M |
| 269 - 271 |
Synthesis of lithium manganese oxides from layered manganese oxides by hydrothermal soft chemical process
Feng Q, Higashimoto Y, Kajiyoshi K, Yanagisawa K |
| 273 - 275 |
Dielectric, pyroelectric and piezoelectric properties of (1-x)Pb(Ni1/3Nb2/3)O-3-x PbTiO3 system
Li ZR, Yao X |
| 277 - 280 |
Synthesis of mesoporous silica material with sodium hexafluorosilicate as silicon source under ultra-low surfactant concentration
Wang L, Tomura S, Suzuki M, Ohashi F, Inukai K, Maeda M |
| 281 - 282 |
Influence of poly(d, l-lactide-b-ethylene glycol) copolymer on morphology and tensile moduli of poly(d,l-lactide) composites containing hydroxyapatite nanocrystals
Deng XM, Hao JY, Yuan ML |
| 283 - 284 |
Synthesis of titanium and tungsten carbides in iron matrices
Jiang WH, Fei J, Han L |
| 285 - 287 |
Deformation behavior below 0.2% offset yield stress in some SiCp/Al composites and their matrix alloys
Zhang F, Li XC, Sun PF, Zhang GD |
| 289 - 291 |
Preparation of high thermal stability MCM-41 in the low surfactant/silicon molar ratio synthesis systems
Yu J, Shi JL, Wang LZ, Ruan ML, Yan DS |
