Powder Technology

Powder Technology, Vol.276 Entire volume, number list

ISSN: 0032-5910 (Print)

In this Issue (26 articles)

1 - 9	Numerical simulation of horizontal jet penetration using filtered fluid model in gas-solid fluidized bed Wang SY, Yang Q, Shao BL, Zhao J, Liu LL, Liu YK
10 - 17	Velocity and orientation distributions of fibrous particles in the near-field of a turbulent jet Qi GQ, Nathan GJ, Lau TCW
18 - 25	Hydrodynamics of particles in liquid-solid packed fluidized bed Mandal D
26 - 33	Flotation and adsorption of muscovite using mixed cationic-nonionic surfactants as collector Wang L, Hu YH, Liu JP, Sun YS, Sun W
34 - 44	Population balance model for biomass milling Gil M, Luciano E, Arauzo I
45 - 59	Effects of radiation on propagating spherical flames of dust-air mixtures Bidabadi M, Azad AV
60 - 65	Effect of firing temperature on the photocatalytic activity of anatase ceramic glazes Tezza VB, Scarpato M, Oliveira LFS, Bernardin AM
66 - 79	A comparison of micromechanical assessments with internal stability/instability criteria for soils Langroudi MF, Soroush A, Shourijeh PT
80 - 88	Mass flow and variability in screw feeding of biomass powders -Relations to particle and bulk properties Falk J, Berry RJ, Brostrom M, Larsson SH
89 - 102	Twin screw granulation - A literature review Seem TC, Rowson NA, Ingram A, Huang ZY, Yu S, de Matas M, Gabbott I, Reynolds GK
103 - 111	Exploring mixing uniformity of a pharmaceutical blend in a high shear mixture granulator using enthalpy values obtained from DSC Bharvada E, Shah V, Misra M
112 - 117	Preparation and excellent microwave absorption properties of ferromagnetic graphene/poly(3, 4-ethylenedioxythiophene)/CoFe2O4 nanocomposites Liu PB, Huang Y, Zhang X
118 - 122	Experimental study for rheological property of exhaustively deionized aqueous suspension of very small colloidal spheres (diameter < ca. 60 nm) Kimura H, Takahashi S, Tsuchida A
123 - 128	Measurements of the wettability of catalyst support materials using the Washburn capillary rise technique Jaine JE, Mucalo MR
129 - 133	Design, synthesis and characterization of a novel orange-yellow long-lasting phosphor: Li2SrSiO4:Eu2+, Dy3+ Cheng SA, Xu XH, Han J, Qiu JB, Zhang BH
134 - 143	Pressure drop and pressure fluctuations in spouted beds with binary mixtures of particles Du W, Zhang LF, Zhang B, Bao SH, Xu J, Wei WS
144 - 155	Computational study of solid circulation in chemical-looping combustion reactor model Geng CM, Zhong WQ, Shao YJ, Chen DL, Jin BS
156 - 165	Effect of material properties and design parameters on the final blend uniformity using experimental and simulation results Florian-Algarin M, Mendez R
166 - 174	Evolution of the microstructure of Cu-Fe-Co-Ni powder mixtures upon mechanical alloying Loginov PA, Levashov EA, Kurbatkina VV, Zaitsev AA, Sidorenko DA
175 - 182	A viscoelastic model for flexible fibers with material damping Nan WG, Wang YS, Tang HP
183 - 192	Vibration sensor approaches for sand detection in oil-water-sand multiphase flow Wang K, Liu ZG, Liu G, Yi LT, Liu PT, Chen M, Peng SQ
193 - 199	Modification of wollastonite by acid treatment and alkali-induced redeposition for use as papermaking filler Xue HL, Wang GS, Hu MY, Chen BW
200 - 203	Low frequency ultrasound assisted synthesis of La0.6Sr0.4Co0.2Fe0.8O3 (-delta) (LSCF) perovskite nanostructures Akbari-Fakhrabadi A, Sathishkumar P, Ramam K, Palma R, Mangalaraja RV
204 - 213	A kinetic description of collisional frictions between particles and solid boundary in simple sheared granular flows Zhang L, Zhong DY, Sun QC, Wu BS
214 - 221	Low temperature hydrothermal synthesis and characterization of iron oxide powders of diverse morphologies from spent pickle liquor Sinha MK, Sahu SK, Meshram P, Prasad LB, Pandey BD
222 - 231	Characterization of carbon nanotube dispersion and filler network formation in melted polyol for nanocomposite materials Pircheraghi G, Foudazi R, Manas-Zloczower I