Powder Technology

Powder Technology, Vol.284 Entire volume, number list

ISSN: 0032-5910 (Print)

In this Issue (67 articles)

1 - 11	Optimization of spray drying process for formulation of solid dispersion containing polypeptide-k powder through quality by design approach Kaur P, Singh SK, Garg V, Gulati M, Vaidya Y
12 - 18	Ball size distribution for the maximum production of a narrowly-sized mill product Chimwani N, Mulenga FK, Hildebrandt D
19 - 24	Effect of furnace pressure drop on heat transfer in a 135 MW CFB boiler Liu XM, Zhang M, Lu JF, Yang HR
25 - 31	Two-dimensional particle shape analysis from chord measurements to increase accuracy of particle shape determination Petrak D, Dietrich S, Eckardt G, Kohler M
32 - 39	Uniformly dispersion of carbon nanotube in aluminum powders by wet shake-mixing approach Peng T, Chang I
40 - 46	Application of ball milling in the synthesis of AA 7075-ZrO2 metal matrix nanocomposite Hernandez-Martinez SE, Cruz-Rivera JJ, Garay-Reyes CG, Elias-Alfaro CG, Martinez-Sanchez R, Hernandez-Rivera JL
47 - 56	An investigation of the effect of particle size on discharge behavior of pulverized coal Liu Y, Lu HF, Guo XL, Gong X, Sun XL, Zhao W
57 - 62	Preparation of basic magnesium carbonate by simultaneous absorption of NH3 and CO2 into MgCl2 solution in an RPB Sun BC, Zhou HJ, Arowo M, Chen JM, Chen JF, Shao L
63 - 77	Random-fractal-method-based generation of meso-model for concrete aggregates Yang X, Wang FL
78 - 84	Thermal conductivity, viscosity and surface tension of nanofluids based on FeC nanoparticles Huminic A, Huminic G, Fleaca C, Dumitrache F, Morjan I
85 - 94	Enhanced photocatalytic degradation of methylene blue by WO3/ZnWO4 composites synthesized by a combination of microwave-solvothermal method and incipient wetness procedure Keereeta Y, Thongtem S, Thongtem T
95 - 111	CFD investigations of particle segregation and dispersion mechanisms inside a polyolefin 8-leg loop reactor of industrial scale Li YH, Ma YT, Reddy RK, Vijay S, Elovainio E, Wurnitsch C, Nandakumar K
112 - 121	The compression behaviors of titanium/carbamide powder mixtures in the preparation of biomedical titanium scaffolds with the space holder method Arifvianto B, Leeflang MA, Zhou J
122 - 129	The onset of particle agglomeration during the dry ultrafine grinding of limestone in a planetary ball mill Guzzo PL, Tino AAA, Santos JB
130 - 142	Effects of the riser exit geometries on the hydrodynamics and solids back-mixing in CFB risers: 3D simulation using CPFD approach Shi XG, Wu YY, Lan XY, Liu F, Gao JS
143 - 148	Preparation and characterization of Bi2Fe4O9/NiFe2O4 composite powders Lin Y, Kang P, Yang HB, Zhang G, Gou ZJ
149 - 158	Effect of ball size on steady state of aluminum powder and efficiency of impacts during milling Razavi-Tousi SS, Szpunar JA
159 - 169	Validation of filtered two-fluid models for gas-particle flows against experimental data from bubbling fluidized bed Ozarkar SS, Yan XK, Wang SY, Milioli CC, Milioli FE, Sundaresan S
170 - 186	Solid components separation from heterogeneous mixtures through turbulence control Nedeff V, Lazar G, Agop M, Eva L, Ochiuz L, Dimitriu D, Vrajitoriu L, Popa C
187 - 194	Experimental determination of parameter effects on the coefficient of restitution of differently shaped maize in three-dimensions Wang LJ, Zhou WX, Ding ZJ, Li XX, Zhang CG
195 - 203	The importance of processing conditions on the biological response to apatites Cox SC, Jamshidi P, Williams RL, Grover LM, Mallick KK
204 - 209	Effects of low-melting temperature salt (Na2SO4) addition on the phase transformation, crystal growth, and chroma of titanium dioxide pigments Wang Y, Mumford KA, Shen SF, Li YJ
210 - 217	Influence of coating MgO with coprecipitation method on sticking during fluidized bed reduction of Fe2O3 particles Guo L, Zhong YW, Gao JT, Yang ZR, Guo ZC
218 - 224	Transportability and pressure drop of fresh cemented coal gangue-fly ash backfill (CGFB) slurry in pipe loop Wu D, Yang BG, Liu YC
225 - 230	Tuning solution chemistry for morphology control of lithium-ion battery precursor particles Robinson JP, Koenig GM
231 - 236	Preparation of silica nanoparticles from waste silicon sludge Ding H, Li JQ, Gao YJ, Zhao D, Shi DJ, Mao GZ, Liu SJ, Tan X
237 - 244	Sol-gel microencapsulation of oil phase with Pickering and nonionic surfactant based emulsions Butstraen C, Salaun F, Devaux E
245 - 252	Effect of cone installation in a pleated filter cartridge during pulse-jet cleaning Li JL, Li SH, Zhou FB
253 - 256	The synthesis of calcium carbonate microparticles with multiple morphologies through self-assembly method Yuan G, Chen XF, Li X, Liang QM, Miao GH, Yuan B
257 - 264	An experimental evaluation of discrete element simulations of confined powder compression using an extended truncated-sphere model Persson AS, Frenning G
265 - 271	Characterization of vaterite synthesized at various temperatures and stirring velocities without use of additives Sevcik R, Perez-Estebanez M, Viani A, Sasek P, Macova P
272 - 278	Fractal process and particle size distribution in a TiH2 powder milling system Liu Y, Wang CM, Zhang YG, Xiao SF, Chen YG
279 - 288	Characterization and measurement of apparent viscosity of solid particles in fixed beds under high temperature Zhang YL, An ZQ, Bai H, Li Q, Guo ZC
289 - 298	Inhalable curcumin formulations by supercritical technology Kurniawansyah F, Mammucari R, Foster NR
299 - 311	Eulerian-Eulerian simulation of irregular particles in dense gas-solid fluidized beds Hua LN, Zhao H, Li J, Wang JW, Zhu QS
312 - 325	Augmentation of natural convective heat transfer in linearly heated cavity by utilizing nanofluids in the presence of magnetic field and uniform heat generation/absorption Mliki B, Abbassi MA, Omri A, Zeghmati B
326 - 335	Dependence of wall stress ratio on wall friction coefficient during the discharging of a 3D rectangular hopper Xu PK, Duan XZ, Qian G, Zhou XG
336 - 343	Performance investigation of micro- and nano-sized particle erosion in a 90 degrees elbow using an ANFIS model Shamshirband S, Malvandi A, Karimipour A, Goodarzi M, Afrand M, Petkovic D, Dahari M, Mahmoodian N
344 - 354	Comparing particle breakage in an uniaxial confined compression test to single particle crush tests-model and experimental results Liburkin R, Portnikov D, Kalman H
355 - 364	Hydrodynamic investigation of gas-solid flow in rectangular spout-fluid bed using CFD-DEM modeling Saidi M, Tabrizi HB, Grace JR, Lim CJ
365 - 370	Scalable synthesis of Si/SiO2@C composite from micro-silica particles for high performance lithium battery anodes Zhou Y, Tian ZY, Fan RJ, Zhao SR, Zhou R, Guo HJ, Wang ZX
371 - 378	Simultaneous measurement of 3D velocity and 2D rotation of irregular particle with digital holographic particle tracking velocimetry Wu YC, Wu XC, Yao LC, Brunel M, Coetmellec S, Lebrun D, Grehan G, Cen K
379 - 386	Design of pulse-jet systems for milk powder baghouses Litchwark JO, Winchester J, Nijdam JJ
387 - 395	A highly reactive and enhanced thermal stability nanocomposite catalyst based on Pt nanoparticles assembled in the inner surface of mesoporous SiO2 spherical shell Zhang C, Zhou YM, Zhang YW, Zhang ZW, Xu YM, Wang QL
396 - 402	Identification of inter-particular forces by atomic force microscopy and how they relate to powder rheological properties measured in shearing tests Colbert MJ, Grandbois M, Abatzoglou N
403 - 410	A model of solids friction factor for fluidized dense phase pneumatic conveying Behera N, Agarwal VK, Jones MG
411 - 417	Prediction of the effect of taste masking on disintegration behavior, mechanical strength and rheological characteristics of highly water soluble drug (itopride HCl); an application of SeDeM-ODT expert system Khan A, Iqbal Z, Ibrahim M, Nasir F, Ullah Z
418 - 428	Rebound characteristics for the impact of SiO2 particle onto a flat surface at different temperatures Li SF, Xie J, Dong M, Bai LY
429 - 436	Ultrasonic technique for concentration characterization of copper nanofluids synthesized using mu-EDM: A novel experimental approach Sahu RK, Hiremath SS, Manivannan PV
437 - 442	Study on the critical amount of liquid for bed material agglomeration in a bubbling fluidized bed Montes A, Hamidi M, Briens C, Berruti F, Tran H, Xu CB
443 - 451	Numerical simulation of loop seal for a circulating fluidized bed based on an improved EMMS bubbling model Zhao M, Zhang N, Liu XH, Du W
452 - 458	Characterization of clay rock samples of a borax ore in relation to their problematical flocculation behavior Cirak M, Hosten C
459 - 466	Complex effects of alloy composition and porosity on the phase transformations and mechanical properties of powder metallurgy steels Park J, Lee S, Kang S, Jeon J, Lee SH, Kim HK, Choi H
467 - 474	The degradation of poly(ethylene glycol) in an Inconel 718 feedstock in the metal injection moulding process Royer A, Barriere T, Gelin JC
475 - 485	Computational study of particle temperature in a bubbling spout fluidized bed with hot gas injection Patil AV, Peters EAJF, Kuipers JAM
486 - 495	Minimal prerequisites for measuring two-dimensional contour roundness in a particle classification context Krupka A, Riha K
496 - 503	Modelling the non-linear elastic behaviour and fracture of metal powder compacts Jonsen P, Haggblad HA, Gustafsson G
504 - 513	Spark plasma sintering of graphite-aluminum powder reinforced with SiC/Si particles Durowoju MO, Sadiku ER, Diouf S, Shongwe MB, Olubambi PA
514 - 520	Effects of density ratio, rotation speed, and fill level on density-induced granular streak segregation in a rotating drum Liao CC, Hsiau SS, Nien HC
521 - 529	Enhanced fluidization of nanoparticles with gas phase pulsation assistance Akhavan A, Rahman F, Wang S, Rhodes M
530 - 540	In situ characterisation of a concentrated colloidal titanium dioxide settling suspension and associated bed development: Application of an acoustic backscatter system Bux J, Peakall J, Biggs S, Hunter TN
541 - 550	Optimizing the degree of carbon nanotube dispersion in a solvent for producing reinforced epoxy matrices Korayem AH, Barati MR, Chen SJ, Simon GP, Zhao XL, Duan WH
551 - 559	Function of upstream and downstream conveying elements in wet granulation processes within a twin screw extruder Liu Y, Thompson MR, O'Donnell KP
560 - 570	Hybrid intelligent model for approximating unconfined compressive strength of cement-based bricks with odd-valued array of peat content (0-29%) Shamshirband S, Tavakkoli A, Roy CB, Motamedi S, Ki-Il S, Hashim R, Islam SM
571 - 584	Dense granular flow - A collaborative study Mort P, Michaels JN, Behringer RP, Campbell CS, Kondic L, Langroudi MK, Shattuck M, Tang J, Tardos GI, Wassgren C
585 - 594	Characterization of crystalline and spray-dried amorphous alpha-cyclodextrin powders Ho TM, Howes T, Bhandari BR
595 - 603	Simulations of flow behavior of oscillatory opposed dilute gas-solid jets Wang SY, Li XY, Fang JY, Zhao J, Liu LL, Liu YK, Liu Y