Powder Technology

Powder Technology, Vol.369 Entire volume, number list

ISSN: 0032-5910 (Print)

In this Issue (28 articles)

1 - 16	Stirred media mills in the mining industry: Material grindability, energy-size relationships, and operating conditions Taylor L, Skuse D, Blackburn S, Greenwood R
17 - 24	Evaluation of the residual moisture content in pilot scale vibrating screening operating with pressure reduction in the screen drying region Menezes AL, Barbosa VP, Malagoni RA, Gedraite R, Ataide CH
25 - 37	Development of organically modified montmorillonite/polypropylene composite powders for selective laser sintering Tan LJ, Zhu W, Zhou K
38 - 52	Experimental investigation of the grade efficiency of a zigzag separator Lukas E, Roloff C, van Wachem B, Thevenin D
53 - 71	Explosion characteristics of aluminum powder in different mixed gas environments Wang XW, Wang ZR, Ni L, Zhu M, Liu CP
72 - 87	A hybrid particle-geometric scaling approach for elasto-plastic adhesive DEM contact models Mohajeri MJ, Helmons RLJ, van Rhee C, Schott DL
88 - 95	A study on the influencing factors and trends of the falling extra-fine aluminium flake dust generation rate Liu WJ, Bai CH, Liu QM, Yao J
96 - 105	Particle number balance approach for simulation of a multi-chamber fluidized bed urea granulator; Modeling and validation Nemati H, Shekoohi SA
106 - 113	Estimating the number-weighted equivalents of the mass-weighted size distribution functions Camalan M
114 - 126	Heat transfer behavior of the immersed tubes and solid circulation rate of a conventional U type loop-seal with an in-line tube bundle in the recycle chamber with and without side aeration at the walls Armatsombat A, Chinsuwan A
127 - 136	Ball-milling properties and sintering behavior of Al-based Gd2O3-W shielding materials used in spent-fuel storage Cong S, Ran G, Li YP, Chen Y
137 - 145	Development and characterization of curcumin-loaded solid self-emulsifying drug delivery system (SEDDS) by spray drying using Soluplus (R) as solid carrier Kamal MM, Salawi A, Lam M, Nokhodchi A, Abu-Fayyad A, El Sayed KA, Nazzal S
146 - 161	Simulation of granular flow in a rotating frame of reference using the discrete element method Delacroix B, Bouarab A, Fradette L, Bertrand F, Blais B
162 - 175	Neural network modeling of thermo-hydraulic attributes and entropy generation of an ecofriendly nanofluid flow inside tubes equipped with novel rotary coaxial double-twisted tape Bahiraei M, Mazaheri N, Hosseini S
176 - 183	Quantification of tablet sensitivity to a stress concentration: Generalization of Hiestand's approach and link with the microstructure Croquelois B, Girardot J, Kopp JB, Tchoreloff P, Mazel V
184 - 201	Analysis of flexible ribbon particle residence time distribution in a fluidised bed riser using three-dimensional CFD-DEM simulation Wu K, Zhang EQ, Yuan ZL, Li B, Zhu WK, Xu J, Wang L, Luo DS
202 - 222	Investigation on the simulation approach for Martian rarefied aeolian activities based on discrete element method Ding TX, Deng ZQ, Hou XY, Liu YM, Liu YF, Li M, Li M
223 - 237	Eulerian-Lagrangian simulation of the full-loop gas-solid hydrodynamics in a pilot-scale circulating fluidized bed Yang SL, Wang S
238 - 247	Experimental analysis of the resistance of packed beds based on the morphology of cylinder Zhang CQ, Gao J, Zeng LJ, Xia YF, Xie WH, Ye W
248 - 260	Lattice Boltzmann investigation on fluid flows through packed beds: Interaction between fluid rheology and bed properties Qi Z, Kuang SB, Qiu TS, Yu AB
261 - 269	Efficacy of hybrid nano-powder presence on the thermal conductivity of the engine oil: An experimental study Tian XX, Kalbasi R, Qi C, Karimipour A, Huang HL
270 - 278	Degradation of polyacrylamide in an ultrasonic-Fenton-like process using an acid-modified coal fly ash catalyst Wang NN, Zhao Q, Li QY, Zhang GS, Huang YL
279 - 288	Preliminary evaluation and studies on the preparation, characterization and in vitro release studies of different biopolymer microparticles for controlled release of folic acid Estevinho BN, Lazar R, Blaga A, Rocha F
289 - 297	A novel model for critical motion of particles in inclined channels o liquid-solid separation fluidized bed He SR, Li YF, Liu TS, Chen P, Zhao YF, Yin M
298 - 310	Development of drag correlation for suspensions of ellipsoidal particles Cao Z, Tafti DK, Shahnam M
311 - 320	Experimental study on the influence of alternating working conditions on the physical properties and stability of ammonia-water nanofluid applied in the practical system Song JW, Jiang WX, Qian H, Du K
321 - 333	Numerical analysis of axial gas flow in cyclone separators with different vortex finder diameters and inlet dimensions Wei Q, Sun GG, Gao CZ
334 - 344	Microstructure evolution and mechanical properties of LaB6-modified Ti2AlNb alloy fabricated by blended elemental powder metallurgy Zhang NB, Han XL, Sun DL, Liu SA, Li H, Yang WS, Wu GH