Powder Technology

Powder Technology, Vol.203, No.2 Entire volume, number list

ISSN: 0032-5910 (Print)

In this Issue (36 articles)

109 - 124	Computational fluid dynamics and electrostatic modeling of polymerization fluidized-bed reactors Rokkam RG, Fox RO, Muhle ME
125 - 132	Numerical and theoretical investigation of the surface flows of granular materials on heaps de Ryck A, Zhu HP, Wu SM, Yu AB, Zulli P
133 - 147	Regrinding sulphide minerals - Breakage mechanisms in milling and their influence on surface properties and flotation behaviour Ye X, Gredelj S, Skinner W, Grano SR
148 - 166	Case studies for selective agglomeration detection in fluidized beds: Application of a new screening methodology Bartels M, Nijenhuis J, Kapteijn F, van Ommen JR
167 - 175	Development of a new abrasion tester based on planetary motion van Laarhoven B, Schaafsma SH, Meesters GMH
176 - 179	Fabrication and characterization of porous silver powder prepared by spray drying and calcining technology Lu HZ
180 - 186	Effects of fluorine ion and mechanical activation on nanostructure forsterite formation mechanism Tavangarian F, Emadi R
187 - 197	Particle velocities and their residence time distribution in the riser of a CFB Chan CW, Seville JPK, Parker DJ, Baeyens J
198 - 205	Experimental characterisation of CaCO3 powder mix for high-pressure compaction modelling Berg S, Jonsen P, Haggblad HA
206 - 210	Fractal dimension of fumed silica: Comparison of light scattering and electron microscope methods Ibaseta N, Biscans B
211 - 222	Investigating the effect of shape on particle segregation using a Monte Carlo simulation Roskilly SJ, Colbourn EA, Alli O, Williams D, Paul KA, Welfare EH, Trusty PA
223 - 236	Experimental study of liquid drop impact onto a powder surface Marston JO, Thoroddsen ST, Ng WK, Tan RBH
237 - 242	Wall effects on the velocities of a single sphere settling in a stagnant and counter-current fluid and rising in a co-current fluid Arsenijevic ZL, Grbavcic ZB, Garic-Grulovic RV, Bakovic-Vragolovic NM
243 - 247	Effect of pH on the morphology and optical properties of modified ZnO particles by SDS via a precipitation method Samaele N, Amornpitoksuk P, Suwanboon S
248 - 253	New model describing the total dispersion of dry powder agglomerates Weiler C, Wolkenhauer M, Trunk M, Langguth P
254 - 264	Determination of particle shape distribution of clay using an automated AFM image analysis method Gelinas V, Vidal D
265 - 271	Hydrothermal mass production of MgBO2(OH) nanowhiskers and subsequent thermal conversion to Mg2B2O5 nanorods for biaxially oriented polypropylene resins reinforcement Zhu WC, Li GD, Zhang Q, Xiang L, Zhu SL
272 - 276	The non-isothermal kinetics analysis of the thermal decomposition of kaolinite by Effluent Gas Analysis technique Ptacek P, Soukal F, Opravil T, Noskova M, Havlica J, Brandstetr J
277 - 287	Fabrication of composite microparticles of artemisinin for dissolution enhancement Sahoo NG, Kakran M, Li L, Judeh Z
288 - 297	An approximate theory for stresses in dust cake of ceramic candle filters Smid J, Chyou YP, Hsiau SS
298 - 309	Removal of emulsified oil from water by inverse fluidization of hydrophobic aerogels Wang D, Silbaugh T, Pfeffer R, Lin YS
310 - 314	Grass blade-like microparticle MnPO4 center dot H2O prepared by a simple precipitation at room temperature Boonchom B, Baitahe R, Joungmunkong Z, Vittayakorn N
315 - 321	Effects of synthesis conditions on the morphology of hydroxyapatite nanoparticles produced by wet chemical process Wang PP, Li CH, Gong HY, Jiang XR, Wang HQ, Li KX
322 - 330	The residence time distribution and mixing of the gas phase in the riser of a circulating fluidized bed Mahmoudi S, Seville JPK, Baeyens J
331 - 347	Computational fluid dynamics modeling of rice husk combustion in a fluidised bed combustor Rozainee M, Ngo SP, Salema AA, Tan KG
348 - 353	Synthesis and characterization of pure single phase Ni-Zn ferrite nanopowders by oxalate based precursor method Sarangi PP, Vadera SR, Patra MK, Ghosh NN
354 - 358	Investigations on air induced segregation of pharmaceutical powders and effect of material flow functions Deng T, Paul KA, Bradley MSA, Immins L, Preston C, Scott JF, Welfare EH
359 - 364	Resistance to airflow through bulk pistachio nuts (Kalleghochi variety) as affected by moisture content, airflow rate, bed depth and fill method Kashaninejad M, Maghsoudlou Y, Khomeiri M, Tabil LG
365 - 370	Determination of dielectric properties of corn seeds from 1 to 100 MHz Sacilik K, Colak A
371 - 383	Three-dimensional modelling of pneumatic drying process Mezhericher M, Levy A, Borde I
384 - 388	Spray drying of TiO2 nanoparticles into redispersible granules Faure B, Lindelov JS, Wahlberg M, Adkins N, Jackson P, Bergstrom L
389 - 396	Optimized experimental design for natural clinoptilolite zeolite ball milling to produce nano powders Charkhi A, Kazemian H, Kazemeini M
397 - 403	Spontaneous inter-particle percolation: A kinematic simulation study Li J, Yu AB, Bridgwater J, Rough SL
404 - 411	Prediction of jet penetration depth based on least square support vector machine Wang CH, Zhong ZP, Li R, E JQ
412 - 414	Selective hydrogenation of citral over gold nanoparticles on alumina Caballero C, Valencia J, Barrera M, Gil A
415 - 418	Microwave-assisted additive free synthesis of nanocrystalline zinc oxide Bhatte KD, Tambade P, Fujita S, Arai M, Bhanage BM