| 273 - 278 |
Supersaturation operation for quality control of crystalline particles in solution crystallization
Takiyama H |
| 279 - 283 |
Nanocrystalline copper doped zinc oxide produced from copper doped zinc hydroxide nitrate as a layered precursor
Ghotbi MY, Bagheri N, Sadrnezhaad SK |
| 284 - 289 |
Synthesis and structural characterization of nanocrystalline (Ni, Fe)(3)Al intermetallic compound prepared by mechanical alloying
Adabavazeh Z, Karimzadeh F, Enayati MH |
| 290 - 297 |
Outflow properties of silos: The effect of arching
Oldal I, Keppler I, Csizmadia B, Fenyvesi L |
| 298 - 304 |
Synthesis of Cu2O nanocrystallites and their adsorption and photocatalysis behavior
Shoeib MA, Abdelsalam OE, Khafagi MG, Hammam RE |
| 305 - 314 |
Wavelet packet analysis of particle response to turbulent fluctuation
Liu J, Wang Y, Yang B |
| 315 - 323 |
Magnetic and catalytic properties of cubic copper ferrite nanopowders synthesized from secondary resources
Rashad MM, Mohamed RM, Ibrahim MA, Ismail LFM, Abdel-Aal EA |
| 324 - 327 |
Synthesis and luminescence properties of YAG:Ce nanopowder prepared by the Pechini method
Hassanzadeh-Tabrizi SA |
| 328 - 333 |
Synthesis of magnetite nanoparticles by surfactant-free electrochemical method in an aqueous system
Fajaroh F, Setyawan H, Widiyastuti W, Winardi S |
| 334 - 337 |
Mechanochemical synthesis of Al2O3/Co nanocomposite by aluminothermic reaction
Hosseini SN, Karimzadeh F, Enayati MH |
| 338 - 342 |
Development of NiFe-CNT and Ni3Fe-CNT nanocomposites by mechanical alloying
Azadehranjbar S, Karimzadeh F, Enayati MH |
| 343 - 348 |
Role of intensive milling in mechano-thermal processing of TiAl/Al2O3 nano-composite
Alamolhoda S, Heshmati-Manesh S, Ataie A |
| 349 - 351 |
Using particle trajectory for determining the fluidization regime in gas-solid fluidized beds
Tamadondar MR, Azizpour H, ZarghamiA R, Mostoufi N, Chaouki J |
| 352 - 357 |
Determination of optimum condition to produce nanocrystalline pyrite by solvothermal synthesis method
E'jazi N, Aghaziarati M |
| 358 - 365 |
Preparation and characterization of the bismuth sodium titanate (Na0.5Bi0.5TiO3) ceramic doped with ZnO
Chou CS, Wu CY, Yang RY, Ho CY |
| 366 - 371 |
The synthesis and characterization of ultrafine grain NiAl intermetallic
Xu GH, Zhang KF, Huang ZQ |
| 372 - 379 |
The best screw shape for fine zinc oxide particles feeding
Dalenjan MB, Jamshidi E, Ebrahim HA |
| 380 - 386 |
Investigating the hydrodynamics of gas-solid bubbling fluidization using recurrence plot
Babaei B, Zarghami R, Sedighikamal H, Sotudeh-Gharebagh R, Mostoufi N |
| 387 - 392 |
Combustion characteristics of the heat pellet prepared from the Fe powders obtained by spray pyrolysis
Kim JH, Koo HY, Hong SK, Han JM, Jang HC, Ko YN, Hong YJ, Kang YC, Kang SH, Cho SB |
| 393 - 397 |
The nanostructure evolution of Ag powder synthesized by high energy ball milling
Khayati GR, Janghorban K |
| 398 - 405 |
Effect of various parameters on bubble formation due to a single jet pulse in two-dimensional coarse-particle fluidized beds
Rong LW, Zhan JM, Wu CL |
| 406 - 413 |
Carbothermal formation and microstrutural evolution of alpha'-Sialon-AlN-BN powders from boron-rich blast furnace slag
Jiang T, Wu JB, Xue XX, Duan PN, Chu MS |
| 414 - 418 |
Adsorption and photocatalysis of nanocrystalline TiO2 particles prepared by sol-gel method for methylene blue degradation
Hwang KJ, Lee JW, Shim WG, Jang HD, Lee SI, Yoo SJ |
| 419 - 425 |
Microstructure and abrasive behaviors of TiC-316L composites prepared by warm compaction and microwave sintering
Lin SJ, Xiong WH |
