Chemical Engineering Research & Design

Chemical Engineering Research & Design, Vol.110 Entire volume, number list

ISSN: 0263-8762 (Print)

In this Issue (26 articles)

1 - 1	Special issue: Foreword-7th International Granulation Workshop Saleh K, Hassanpour A, Ghadiri M, Selman A
2 - 11	Reduction of energy consumption in batch fluidized bed layering granulation processes by temporal separation Mielke L, Hoffmann T, Henneberg M, Peglow M, Buck A, Tsotsas E
12 - 19	De-mixing characteristics of fine coal in an air dense medium fluidized bed Zhao PF, Zhu R, Zhao YM, Luo ZF
20 - 31	Measurement of particle concentration in a Wurster coater draft tube using light attenuation Sibanc R, Zun I, Dreu R
32 - 42	Dispersion of a semi-solid binder in a moving powder bed during detergent agglomeration Balashanmugam M, Cheong YS, Alam Z, Hounslow MJ, Salman AD
43 - 53	Twin screw granulation: Understanding the mechanism of granule formation along the barrel length Lute SV, Dhenge RM, Hounslow MJ, Salman AD
54 - 61	Selective agglomeration of fine coal using a water-in-oil emulsion van Netten K, Moreno-Atanasio R, Galvin KP
62 - 69	Liquisolid technology applied to pellets: Evaluation of the feasibility and dissolution performance using felodipine as a model drug Pezzini BR, Beringhs AO, Ferraz HG, Silva MAS, Stulzer HK, Sonaglio D
70 - 81	Design, production and characterisation of granular adsorbent material for arsenic removal from contaminated wastewater Mangwandi C, Suhaimi SNA, Liu JT, Dhenge RM, Albadarin AB
82 - 97	Specific energy consumption and quality of wood pellets produced using high-moisture lodgepole pine grind in a flat die pellet mill Tumuluru JS
98 - 107	Effect of silica nanoparticles to prevent calcium carbonate scaling using an in situ turbidimetre Al Nasser WN, Shah VV, Nikiforou K, Petrou P, Heng JYY
108 - 113	A novel technique for quantifying the cohesive strength of washcoat Yang JK, Holt EM, Blanco-Garcia P, Wagland A, Hounslow MJ, Salman AD
114 - 122	Finite volume approximations of breakage population balance equation Saha J, Kumar J, Buck A, Tsotsas E
123 - 130	A new contact liquid dispersion model for discrete particle simulation Washino K, Miyazaki K, Tsuji T, Tanaka T
131 - 140	Predicting the surface composition of a spray-dried particle by modelling component reorganization in a drying droplet Porowska A, Dosta M, Fries L, Gianfrancesco A, Heinrich S, Palzer S
141 - 151	Finite element analysis of thermomechanical behaviour of powders during tabletting Krok A, Garcia-Trinanes P, Peciar M, Wu CY
152 - 159	Characterisation of the work of adhesion of food grade coating materials on a maltodextrin model surface Kape A, Ruick B, Drusch S
160 - 170	Movement of a secondary immiscible liquid in a suspension using a non-invasive technique Islam SF, Sundara RV, Whitehouse S, Althaus TO, Palzer S, Hounslow MJ, Salman AD
171 - 182	Evaluation of the ability of powdered milk to produce minitablets containing paracetamol for the paediatric population Pinto JT, Brachkova MI, Fernandes AI, Pinto JF
183 - 191	Compression analysis for assessment of pellet plasticity: Identification of reactant pores and comparison between Heckel, Kawakita, and Adams equations Persson AS, Nordstrom J, Frenning G, Alderborn G
192 - 199	Amorphous solid dispersions of BCS class II drugs: A rational approach to solvent and polymer selection Davis MT, Egan DP, Kuhs M, Albadarin AB, Griffin CS, Collins JA, Walker GM
200 - 208	Drop impact behaviour on alternately hydrophobic and hydrophilic layered bead packs Atherton S, Polak D, Hamlett CAE, Shirtcliffe N, McHale G, Ahn S, Doerr SH, Bryant R, Newton MI
209 - 219	Experimental study of oblique impact of particles on wet surfaces Cruger B, Heinrich S, Antonyuk S, Deen NG, Kuipers JAM
220 - 232	Stearic acid crystals stabilization in aqueous polymeric dispersions Jarray A, Gerbaud V, Hemati M
233 - 244	Influence of liquid formulation and impact conditions on the wetting of hydrophobic surfaces by aqueous polymeric solutions Khoufech A, Benali M, Saleh K
245 - 254	An overview of the role of capillary condensation in wet caking of powders Afrassiabian Z, Leturia M, Benali M, Guessasma M, Saleh K