| 1 - 8 |
Desorption of crude oil components from silica and aluminosilicate surfaces upon exposure to aqueous low salinity and surfactant solutions
Nourani M, Tichelkamp T, Gawel B, Oye G |
| 9 - 19 |
Effect of intake air temperature and common-rail pressure on ethanol combustion in a single-cylinder light-duty diesel engine
Woo C, Kook S, Hawkes ER |
| 20 - 26 |
Synthesis, characterization, and mechanism of asphaltene inhibition of phosphopropoxylated asphaltenes
Ovalles C, Rogel E, Morazan H, Moir ME |
| 27 - 33 |
CO2 continuous removal using ion exchange as regeneration process
Gomez-Diaz D, Navaza JM |
| 34 - 40 |
Effect of oxygen and additives on thermal decomposition of aqueous urea solution
Wang DH, Hui SE, Liu CC, Zhuang HY |
| 41 - 49 |
Influence of engine load and speed on regulated and unregulated emissions of a diesel engine fueled with diesel fuel blended with waste cooking oil biodiesel
Man XJ, Cheung CS, Ning Z, Wei L, Huang ZH |
| 50 - 58 |
Effect of additives on interfacial interactions for viscosity reduction of carbonaceous solid-water slurries
Mukherjee A, Pisupati SV |
| 59 - 70 |
Determination of minimum miscibility pressure in CO2-IOR projects with the aid of hybrid neuro-fuzzy system
Mollaiy-Berneti S |
| 71 - 79 |
Thermal and thermo-oxidative characterisation of rice straw for its use in energy valorisation processes
Moliner C, Bosio B, Arato E, Ribes A |
| 80 - 89 |
Effect two grades of octane numbers on the performance, exhaust and acoustic emissions of spark ignition engine
Alahmer A, Aladayleh W |
| 90 - 96 |
An investigation on the effects of using DEE additive in a DI diesel engine fuelled with waste plastic oil
Kaimal VK, Vijayabalan P |
| 97 - 105 |
Recovery potentials of cenospheres from bituminous coal fly ashes
Acar I, Atalay MU |
| 106 - 115 |
Experimental study of anisotropic gas permeability and its relationship with fracture structure of Longmaxi Shales, Sichuan Basin, China
Ma Y, Pan ZJ, Zhong NN, Connell LD, Down DI, Lin WL, Zhang Y |
| 116 - 126 |
Characterisation of tar from sewage sludge gasification. Influence of gasifying conditions: Temperature, throughput, steam and use of primary catalysts
de Andres JM, Roche E, Narros A, Rodriguez ME |
| 127 - 136 |
Oxidation by H2O2 of bezothiophene and dibenzothiophene over different polyoxometalate catalysts in the frame of ultrasound and mixing assisted oxidative desulfurization
Choi AES, Roces S, Dugos N, Wan MW |
| 137 - 147 |
Comparative assessment of a porous burner using vegetable cooking oil-kerosene fuel blends for thermoelectric and thermophotovoltaic power generation
Mustafa KF, Abdullah S, Abdullah MZ, Sopian K |
| 148 - 156 |
Oil shale separation using a novel combined dry beneficiation process
Yu XD, Luo ZF, Yang XL, Jiang HS, Zhou EH, Zhang B, Dong L |
| 157 - 163 |
Experimental observations of turbulent flame propagation effected by flame acceleration in the end gas of closed combustion chamber
Wei HQ, Gao DZ, Zhou L, Pan JY, Tao K, Pei ZG |
| 164 - 174 |
Comparative analysis of effect of methanol and ethanol on Karanja biodiesel production and its optimisation
Verma P, Sharma MP |
| 175 - 186 |
A blending rule for octane numbers of PRFs and TPRFs with ethanol
AlRamadan AS, Sarathy SM, Khurshid M, Badra J |
| 187 - 193 |
Anti-agglomeration of natural gas hydrates in liquid condensate and crude oil at constant pressure conditions
Zhao HJ, Sun MW, Firoozabadi A |
| 194 - 204 |
Actual mercury speciation and mercury discharges from coal-fired power plants in Inner Mongolia, Northern China
Tang SL, Wang LN, Feng XB, Feng ZH, Li RY, Fan HP, Li K |
| 205 - 210 |
Catalytic upgrading of coal gaseous tar over Y-type zeolites
Kong XJ, Bai YH, Yan LJ, Li F |
| 211 - 217 |
Kinetic studies on oil extraction and biodiesel production from underutilized Annona squamosa seeds
Subramanian PK, Muthiah P |
| 218 - 227 |
New trend for the pour point depression of a waxy petroleum fraction with in-situ desulphurization using (O2H & OH) radicals coupled with nanoparticles of titanium compounds
El Naggar AMA, Mostafa MS, Zaky MT |
| 228 - 243 |
Analysis of capillary pressure and relative permeability hysteresis under low-salinity waterflooding conditions
Wang X, Alvarado V |
| 244 - 255 |
Production of green aromatics via catalytic cracking of Canola Oil Methyl Ester (CME) using HZSM-5 catalyst with different Si/Al ratios
Bayat A, Sadrameli SM, Towfighi J |
| 256 - 262 |
Influence of minerals on the thermal processing of bamboo with a suite of carbonaceous materials
Yan JF, Shi KQ, Pang CH, Lester E, Wu T |
| 263 - 269 |
Effect of leaf extract from Pongamia pinnata on the oxidation stability, performance and emission characteristics of calophyllum biodiesel
Ramalingam S, Govindasamy M, Ezhumalai M, Kaliyaperumal A |
| 270 - 277 |
Catalytic gasification of carbon in a direct carbon fuel cell
Rady AC, Giddey S, Kulkarni A, Badwal SPS, Bhattacharya S |
| 278 - 283 |
Effect of hydrazides as fuel additives for biodiesel and biodiesel blends on NOx formation
Bar F, Hopf H, Knorr M, Schroder O, Krahl J |
| 284 - 291 |
Comparison of the metal-organic framework MIL-101 (Cr) versus four commercial adsorbents for nitrogen compounds removal in diesel feedstocks
Laredo GC, Vega-Merino PM, Montoya-de la Fuente JA, Mora-Vallejo RJ, Meneses-Ruiz E, Castillo JJ, Zapata-Rendon B |
| 292 - 300 |
Near-nozzle dynamics of diesel spray under varied needle lifts and its prediction using analytical model
Huang WD, Moon S, Ohsawa K |
| 301 - 313 |
Investigation of thermal stimulation of coal seam gas fields for accelerated gas recovery
Shahtalebi A, Khan C, Dmyterko A, Shukla P, Rudolph V |
| 314 - 323 |
Influence of hydrothermal treatment on filterability of fine solids in bitumen froth
Chen Q, Stricek I, Cao ML, Gray MR, Liu Q |
| 324 - 331 |
Combustion tests of grape marc in a multi-fuel domestic boiler
Schonnenbeck C, Trouve G, Valente M, Garra P, Brilhac JF |
| 332 - 342 |
Liquid-liquid equilibrium data for systems important in biodiesel production, involving vegetable oils plus ethyl esters plus monoacylglycerols and diacylglycerols plus anhydrous ethanol, at 303.15 and 318.15 K
Shiozawa S, Meirelles AJA, Batista EAC |
| 343 - 347 |
Effect of the addition of glycerol on hydrogen production from industrial municipal solid waste
Zahedi S, Solera R, Garcia-Morales JL, Sales D |
| 348 - 356 |
Prediction of carbon, hydrogen, and oxygen compositions of raw and torrefied biomass using proximate analysis
Nhuchhen DR |
| 357 - 366 |
Hydraulic characterization of diesel engine single-hole injectors
Payri R, Gimeno J, Cuisano J, Arco J |
| 367 - 376 |
Comparison of the effects of dispersed noble metal (Pd) biomass supported catalysts with typical hydrogenation (Pd/C, Pd/Al2O3) and hydrotreatment catalysts (CoMo/Al2O3) for in-situ heavy oil upgrading with Toe-to-Heel Air Injection (THAI)
Hart A, Omajali JB, Murray AJ, Macaskie LE, Greaves M, Wood J |
| 377 - 383 |
Fitting performance of artificial neural networks and empirical correlations to estimate higher heating values of biomass
Estiati I, Freire FB, Freire JT, Aguado R, Olazar M |
| 384 - 395 |
A multicomponent diffusion model for gas charges into oil reservoirs
Pan S, Zuo JLY, Wang K, Chen Y, Mullins OC |
| 396 - 406 |
Partially premixed low temperature combustion using dimethyl carbonate (DMC) in a DI diesel engine for favorable smoke/NOx emissions
Kumar BR, Saravanan S |
| 407 - 416 |
Effect of gasification agent on co-gasification of rice production wastes mixtures
Pinto F, Andre R, Miranda M, Neves D, Varela F, Santos J |
| 417 - 423 |
Turnover rates for the supercritical water reforming of glycerol on supported Ni and Ru catalysts
Ortiz FJG, Campanario FJ, Ollero P |
| 424 - 432 |
The combined effect of plastics and food waste accelerates the thermal decomposition of refuse-derived fuels and fuel blends
Edo M, Budarin V, Aracil I, Persson PE, Jansson S |
| 433 - 441 |
Development of multi-component diesel surrogate fuel models - Part I: Validation of reduced mechanisms of diesel fuel constituents in 0-D kinetic simulations
Poon HM, Pang KM, Ng HK, Gan SY, Schramm J |
| 442 - 447 |
Determination of cloud point in binary and ternary mixtures containing biodiesel and diesel constituents. Part I - Ethyl palmitate, ethyl stearate and n-hexadecane
Moura-Nickel CD, da Cruz LCC, Igarashi-Mafra L, Yamamoto CI, Rolemberg MP, Mafra MR |
| 448 - 456 |
Cu-impregnated alumina/silica bed materials for Chemical Looping Reforming of biomass gasification gas
Keller M, Fung J, Leion H, Mattisson T |
| 457 - 472 |
Physical properties of heavy oil distillation cuts
Sanchez-Lemus MC, Schoeggl F, Taylor SD, Yarranton HW |
| 473 - 480 |
Hydrothermal dewatering of a Chinese lignite and properties of the solid products
Liao JJ, Fei Y, Marshall M, Chaffee AL, Chang LP |
| 481 - 496 |
Effects of fuel physical properties on direct injection spray and ignition behavior
Kim D, Martz J, Violi A |
| 497 - 505 |
Application of air classification and formulation to manage feedstock cost, quality and availability for bioenergy
Thompson VS, Lacey JA, Hartley D, Jindra MA, Aston JE, Thompson DN |
| 506 - 513 |
The effects of deposits on spray behaviors of a gasoline direct injector
Song HY, Xiao J, Chen YY, Huang Z |
| 514 - 520 |
Modelling of spray evaporation and penetration for alternative fuels
Azami MH, Savill M |
| 521 - 528 |
Propagation characteristics of induced shock waves generated by diesel spray under ultra-high injection pressure
Jia TM, Li GX, Yu YS, Xu YJ |
| 529 - 537 |
Thermal oxidation study of Moroccan oil shale: A new approach to non-isothermal kinetics based on deconvolution procedure
Moine EC, Tangarfa M, Khachani M, El Hamidi A, Halim M, Arsalane S |
| 538 - 550 |
Formation of extremely fine water droplets in sheared, concentrated bitumen solutions via surfactant-mediated tip streaming
Sonthalia R, Ng S, Ramachandran A |
| 551 - 557 |
Biosurfactant, solvents and polymer production by Bacillus subtilis RI4914 and their application for enhanced oil recovery
Fernandes PL, Rodrigues EM, Paiva FR, Ayupe BAL, McInerney MJ, Totola MR |
| 558 - 564 |
The effects of varying spark timing on the performance and emission characteristics of a gasoline engine: A study on Saudi Arabian RON91 and RON95
Binjuwair S, Alkudsi A |
| 565 - 573 |
Numerical and experimental analysis of the effect of adding water electrolysis products on the laminar burning velocity and stability of lean premixed methane/air flames at sub-atmospheric pressures
Echeverri-Uribe C, Amell AA, Rubio-Gaviria LM, Colorado A, Mcdonell V |
| 574 - 579 |
Kinetics of transesterification of palm oil under conventional heating and microwave irradiation, using CaO as heterogeneous catalyst
Ye W, Gao YJ, Ding H, Liu MC, Liu SJ, Han X, Qi JL |
| 580 - 590 |
Liquid slip flow in a network of shale noncircular nanopores
Afsharpoor A, Javadpour F |
| 591 - 596 |
Solid fuel production by hydrothermal carbonization of water-like phase of bio-oil
Fu Y, Ye J, Chang J, Lou H, Zheng XW |
| 597 - 605 |
Attempts to produce blast furnace coke from Victorian brown coal. 3. Hydrothermally dewatered and acid washed coal as a blast furnace coke precursor
Mollah MM, Marshall M, Sakurovs R, Jackson WR, Chaffee AL |
| 606 - 612 |
Biomass composition and ash melting behaviour of selected miscanthus genotypes in Southern Germany
Iqbal Y, Lewandowski I |
| 613 - 623 |
Characterization of particle number and mass size distributions from a small compression ignition engine operating in diesel/methane dual fuel mode
Di Iorio S, Magno A, Mancaruso E, Vaglieco BM |
| 624 - 629 |
Ultrasound assisted biodiesel production in presence of dolomite catalyst
Korkut I, Bayramoglu M |
| 630 - 637 |
Optimization of the operating parameters based on Taguchi method in an SI engine used pure gasoline, ethanol and methanol
Balki MK, Sayin C, Sarikaya M |
| 638 - 644 |
Viscosity measurements of the SiO2-K2O-CaO system relevant to biomass slags
Chen M, Zhao BJ |
| 645 - 652 |
Engine displacement modularity for enhancing automotive s.i. engines efficiency at part load
Millo F, Mirzaeian M, Luisi S, Doria V, Stroppiana A |
| 653 - 658 |
Characterization of organic and black carbon aerosol formation during coal combustion: An experimental study in a 1 MW pilot scale coal combustor
Wang XF, Jing H, Dhungel B, Wang WN, Kumfer BM, Axelbaum RL, Biswas P |
| 659 - 667 |
Numerical study on catalytic combustion and extinction characteristics of pre-mixed methane-air in micro flatbed channel under different parameters of operation and wall
Yan YF, Huang WP, Tang WM, Zhang L, Li LX, Ran J, Yang ZQ |
| 668 - 678 |
Extraction, characterization, purification and catalytic upgrading of algae lipids to fuel-like hydrocarbons
Santillan-Jimenez E, Pace R, Marques S, Morgan T, McKelphin C, Mobley J, Crocker M |
| 679 - 686 |
Microbial hydrolysis and fermentation of rice straw for ethanol production
Wu XD, Zhang JS, Xu EN, Liu YH, Cheng YL, Addy M, Zhou WG, Griffith R, Chen P, Ruan R |
| 687 - 693 |
ANFIS based prediction model for biomass heating value using proximate analysis components
Akkaya E |
| 694 - 717 |
Closed-cycle gas turbine for power generation: A state-of-the-art review
Olumayegun O, Wang MH, Kelsall G |
| 718 - 726 |
Novel molecular simulation process design of adsorption in realistic shale kerogen spherical pores
Zhou B, Xu RN, Jiang PX |
| 727 - 736 |
Synergistic catalytic removals of NO, CO and C3H8 over CeSn0.8W0.6Ox/TiAl0.2Si0.1Ox
Shen YS, Zong YH, Ma YF, Zhu SM, Jin QJ |
| 737 - 742 |
Superior catalytic effect of calcium oxide on the hydrogasification of char for CH4
Jiang JT, Liu QY, Liu ZY |
| 743 - 748 |
Wettability of natural microcrystalline graphite filler with pitch in isotropic graphite preparation
Li K, Shen K, Huang ZH, Shen WC, Yang GZ, Yang JH, Kang FY |
| 749 - 758 |
Catalytic conversion of aqueous fraction of bio-oil to alcohols over CNT-supported catalysts
Zhou MH, Xiao GM, Wang K, Jiang JC |
| 759 - 766 |
Preparation and characterization of phosphotungstic acid/PVA nanofiber composite catalytic membranes via electrospinning for biodiesel production
Shi WY, Li HB, Zhou R, Qin XH, Zhang HX, Su YH, Du QY |
| 767 - 776 |
Hydrodeoxygenation of dibenzofuran to bicyclic hydrocarbons using bimetallic Cu-Ni catalysts supported on metal oxides
Ambursa MM, Ali TH, Voon LH, Sudarsanam P, Bhargava SK, Abd Hamid SB |
| 777 - 784 |
Synthesis of gamma-Al2O3 nanofibers stabilized Co3O4 nanoparticles as highly active and stable Fischer-Tropsch synthesis catalysts
Liu CC, Hong JP, Zhang YH, Zhao YX, Wang L, Wei L, Chen SF, Wang GH, Li JL |
| 785 - 793 |
Fractographic approach to metallurgical coke failure analysis. Part 1: Cokes of single coal origin
Roest R, Lomas H, Hockings K, Mahoney MR |
| 794 - 802 |
Fractographic approach to metallurgical coke failure analysis. Part 2: Cokes from binary coal blends
Roest R, Lomas H, Mahoney MR |
| 803 - 812 |
Fractographic approach to metallurgical coke failure analysis. Part 3: Characterisation of fracture mechanisms in a blast furnace coke
Roest R, Lomas H, Gupta S, Kanniala R, Mahoney MR |
