저변형률속도에서 ARB가공된 무산소동의 미세조직 및 기계적 성질

이성희; 한승전; 임차용; Seong-Hee Lee; Seung-Zeon Han; Cha-Yong Lim

Korean Journal of Materials Research, Vol.17, No.10, 521-525, October, 2007

DOI10.3740/MRSK.2007.17.10.521 Export Citation

저변형률속도에서 ARB가공된 무산소동의 미세조직 및 기계적 성질

Microstructure and Mechanical Properties of Oxygen Free Copper Processed by ARB at Low Strain Rate

이성희^†, 한승전¹, 임차용¹

목포대학교 신소재공학과
¹한국기계연구원 부설 재료연구소

Seong-Hee Lee^†, Seung-Zeon Han¹, and Cha-Yong Lim¹

Department of Advanced Materials Science and Engineering, Mokpo National University, Muan-gun, Chnooam, 534-729, Korea
¹Department of Materials Technology, Korea Institute of Materials Science, 66 Sangnam-dong, Changwon, 641-010, Korea

E-mail:

The microstructure and mechanical properties of an oxygen free copper processed by accumulative roll bonding(ARB) at low strain rate were studied. The copper sheets were highly strained up to an equivalent strain of by ARB process at ambient temperature. The strain rate of the copper during the ARB was . The microstructure and mechanical properties of the ARB-processed copper were compared to those of the specimens processed by ARB at relatively high strain rate (). The microstructure and mechanical properties of the copper with ARB process was very similar to each other despite of some differences in recovery.

Keywords:Accumulative roll-bonding;Strain rate;Oxygen free copper;TEM microstructure;Mechanical property

[References]

Valiev RZ, Krasilnikov NA, Tsenev NK, Mater. Sci. Eng. A, 137, 35 (1991)
Valiev RZ, Chmelik F, Bordeaux F, Kapwlski G, Baudelet B, Scripta Metall. Mater., 27, 855 (1992)
Saito Y, Tsuji N, Utsunomiya H, Sakai T, Hong RG, Scripta Mater., 39, 1221 (1998)
Tsuji N, Saito Y, Utsunomiya H, Tanigawa S, Scripta Mater., 40, 795 (1999)
Lee SH, Saito Y, Tsuji N, Utsunomiya H, Sakai T, Scripta Mater., 46, 281 (2002)
Lee SH, Saito Y, Sakai T, Utsunomiya H, Mater. Sci. Eng. A, 325, 228 (2002)
Lee SH, Saito Y, Park KT, Shin DH, Mater. Trans., 43, 2320 (2002)
Lee SH, Inagaki H, Utsunomiya H, Saito Y, Sakai T, Mater. Trans., 44, 1376 (2003)
Saito Y, Utsunomiya H, Suzuki H, Proc. Inst. Mech. Eng. Ser. B, 215, 947 (2001)
Huang JY, Zhu YT, Jiang H, Lowe TC, Acta Mater., 49, 1497 (2001)
Jang YH, Kim SS, Han SZ, Lim CY, Kim CJ, Goto M, Scripta Mater., 52, 21 (2005)
Lee SH, Cho J, Han SZ, Lim CY, Korean J. Mater. Res., 15(4), 240 (2005)
Lee SH, Cho J, Lee CH, Han SZ, Lim CY, Korean J. Mater. Res., 15(9), 555 (2005)
Lee SH, Kim CS, Kim SS, Han SZ, Lim CY, Korean J. Mater. Res., 17(7), 361 (2007)
Tsuji N, Toyota T, Minamino Y, Koizumi Y, Yamane T, Komatsu M, Kiritani M, Mater. Sci. Eng. A, 350, 108 (2003)

[Referenced By]

[1] Valiev RZ, Krasilnikov NA, Tsenev NK, Mater. Sci. Eng. A, 137, 35 (1991)

[2] Valiev RZ, Chmelik F, Bordeaux F, Kapwlski G, Baudelet B, Scripta Metall. Mater., 27, 855 (1992)

[3] Saito Y, Tsuji N, Utsunomiya H, Sakai T, Hong RG, Scripta Mater., 39, 1221 (1998)

[4] Tsuji N, Saito Y, Utsunomiya H, Tanigawa S, Scripta Mater., 40, 795 (1999)

[5] Lee SH, Saito Y, Tsuji N, Utsunomiya H, Sakai T, Scripta Mater., 46, 281 (2002)

[6] Lee SH, Saito Y, Sakai T, Utsunomiya H, Mater. Sci. Eng. A, 325, 228 (2002)

[7] Lee SH, Saito Y, Park KT, Shin DH, Mater. Trans., 43, 2320 (2002)

[8] Lee SH, Inagaki H, Utsunomiya H, Saito Y, Sakai T, Mater. Trans., 44, 1376 (2003)

[9] Saito Y, Utsunomiya H, Suzuki H, Proc. Inst. Mech. Eng. Ser. B, 215, 947 (2001)

[10] Huang JY, Zhu YT, Jiang H, Lowe TC, Acta Mater., 49, 1497 (2001)

[11] Jang YH, Kim SS, Han SZ, Lim CY, Kim CJ, Goto M, Scripta Mater., 52, 21 (2005)

[12] Lee SH, Cho J, Han SZ, Lim CY, Korean J. Mater. Res., 15(4), 240 (2005)

[13] Lee SH, Cho J, Lee CH, Han SZ, Lim CY, Korean J. Mater. Res., 15(9), 555 (2005)

[14] Lee SH, Kim CS, Kim SS, Han SZ, Lim CY, Korean J. Mater. Res., 17(7), 361 (2007)

[15] Tsuji N, Toyota T, Minamino Y, Koizumi Y, Yamane T, Komatsu M, Kiritani M, Mater. Sci. Eng. A, 350, 108 (2003)