International Journal of Heat and Mass Transfer

International Journal of Heat and Mass Transfer, Vol.124 Entire volume, number list

ISSN: 0017-9310 (Print)

In this Issue (117 articles)

1 - 10	A new rate-transient analysis model for shale gas reservoirs coupled the effect of slip flow and surface diffusion Miao YA, Li XF, Zhou YJ, Lee J, Sun Z, Chang YC, Wang S, Hou CH
11 - 19	A computational and experimental study of thermal energy separation by swirl Kobiela B, Younis BA, Weigand B, Neumann O
20 - 35	Experimental investigation of hydronic air coil performance with nanofluids Strandberg R, Das D
36 - 45	Innovative analytic and experimental methods for thermal management of SMD-type LED chips Jang H, Lee JH, Byon C, Lee BJ
46 - 57	Thermodynamic optimization for an air-standard irreversible Dual-Miller cycle with linearly variable specific heat ratio of working fluid Wu ZX, Chen LG, Ge YL, Sun FR
58 - 73	Buoyancy-driven flow of nanofluids in an inclined enclosure containing an adiabatic obstacle with heat generation/absorption: Effects of periodic thermal conditions Ahmed SE, Elshehabey HM
74 - 82	Approximate, analytical procedure for rectangular annular fins by accommodating the Cauchy-Euler equation Campo A, Delgado-Torres AM
83 - 89	Quantitative measurements of nanoscale thin frost layers using surface plasmon resonance imaging Jeong CH, Shin DH, Konduru V, Allen JS, Choi CK, Lee SH
90 - 108	Heat transfer and fluid flow characteristics of a pair of interacting dual swirling flame jets impinging on a flat surface Singh P, Chander S
109 - 123	Mixing improvement induced by the combination of a micro-ramp with an air porthole in the transverse gaseous injection flow field Li LQ, Huang W, Yan L, Li SB, Liao L
124 - 130	Numerical and experimental investigation on thermal shock failure of Y2O3-coated CVD ZnS infrared windows Liu X, Zhu JQ, Han JC
131 - 140	Cascade-like and cyclic heat transfer characteristics affected by enclosure aspect ratios for low Prandtl numbers Wang B, Shih TM, Chen XW, Chang RRG, Wu CX
141 - 149	Effect of non-condensable gas on pressure oscillation of submerged steam jet condensation in condensation oscillation regime Li WC, Meng ZM, Wang JJ, Sun ZN
150 - 157	Novel measurement of receding wicked liquid responsible for critical heat flux enhancement Son HH, Kim N, Kim SJ
158 - 167	Nanofluid flow and heat transfer in a microchannel with interfacial electrokinetic effects Zhao QK, Xu H, Tao LB
168 - 176	Total hemispherical apparent radiative properties of the infinite V-groove with specular reflection Mulford RB, Collins NS, Farnsworth MS, Jones MR, Iverson BD
177 - 189	The research on the heat source characteristics and the equivalent heat source of the arc in gaps Liu K, Yang F, Wang SH, Gao B, Xu C
190 - 200	Effect of CNT coating on the overall thermal conductivity of unidirectional polymer hybrid nanocomposites Hassanzadeh-Aghdam MK, Mahmoodi MJ, Jamali J
201 - 209	Thermal diode using controlled capillary in heterogeneous nanopores Avanessian T, Hwang G
210 - 219	Experimental study on boiling heat transfer of a self-rewetting fluid on copper foams with pore-density gradient structures Zhou LP, Li W, Ma TX, Du XZ
220 - 232	Numerical simulation of natural convection in a horizontal enclosure: Part I. On the effect of adiabatic obstacle in middle Lee JR
233 - 246	Non-uniform ground-level wind patterns in a heat dome over a uniformly heated non-circular city Fan YF, Li YG, Yin S
247 - 259	Numerical analysis and optimization study on shell-side performances of a shell and tube heat exchanger with staggered baffles Wang XT, Zheng NB, Liu ZC, Liu W
260 - 268	A simplified energy dissipation based model of heat transfer for post-dryout flow boiling Mikielewicz J, Mikielewicz D
269 - 278	Numerical modeling of flow film boiling in cryogenic chilldown process using the AIAD framework Chen JY, Zeng RR, Zhang XB, Qiu LM, Xie JL
279 - 287	Evaporation-induced receding contact lines in partial-wetting regime on a heated substrate Mehrizi AA, Wang H
288 - 297	Assessment of a new method for determining the relationship between effective diffusivity and moisture concentration - Exemplified by autoclaved aerated concrete of four density classes Garbalinska H, Stasiak M, Bochenek M, Musielak G
298 - 306	Triple diffusive mixed convection from an exponentially decreasing mainstream velocity Patil PM, Roy M, Shashikant A, Roy S, Momoniat E
307 - 318	Water droplet impacting on overheated random Si nanowires Auliano M, Fernandino M, Zhang P, Dorao CA
319 - 330	A comparison study on the thermal effects in DBD plasma actuation and electrical heating for aircraft icing mitigation Liu Y, Kolbakir C, Hu HY, Hu H
331 - 343	Direct and inverse approaches for analysis and optimization of fins under sensible and latent heat load Das R, Kundu B
344 - 367	MHD mixed convection of viscoplastic fluids in different aspect ratios of a lid-driven cavity using LBM Kefayati GR, Tang H
368 - 380	Conjugate natural convection heat transfer in an open-ended square cavity partially filled with porous media Chen S, Gong W, Van YY
381 - 389	Slag adhesion on the refractory sensor for molten steel level measurement He Q, Xie Z
390 - 413	Role of differential vs Rayleigh-Benard heating at curved walls for efficient processing via entropy generation approach Biswal P, Basak T
414 - 422	In situ characterization of enhanced thermal performance by periodic nanostructures on the surface of a microchannel Yu J, Kang SW, Kwon TS, Banerjee D
423 - 453	Review of pool boiling enhancement with additives and nanofluids Liang GT, Mudawar I
454 - 462	New friction factor and Nusselt number equations for turbulent convection of liquids with variable properties in circular tubes Zhao HJ, Li XW, Wu XX
463 - 474	Effect of nano-structure coating on thermal performance of thermosyphon boiling in micro-channels Li SF, Bao YY, Wang PY, Liu ZH
475 - 483	Evaluation of the WSGG model against line-by-line calculation of thermal radiation in a non-gray sooting medium representing an axisymmetric laminar jet flame Centeno FR, Brittes R, Rodrigues LGP, Coelho FR, Franca FHR
484 - 490	Experimental study of augmented flow boiling in a dielectric fluid due to backward and forward facing stepped microchannels Gao L, Bhavnani SH
491 - 503	Similarity-solution-based improvement of gamma-Re-theta t model for hypersonic transition prediction Wang YT, Li YW, Xiao LH, Zhang BL, Li YH
504 - 516	Numerical analysis of heat transfer and fluid flow in multilayer deposition of PAW-based wire and arc additive manufacturing Bai XW, Colegrove P, Ding JL, Zhou XM, Diao CL, Bridgeman P, Honnige JR, Zhang HO, Williams S
517 - 532	Experimental investigation of heat transfer characteristics and wall pressure distribution of swirling coaxial confined impinging air jets Markal B
533 - 542	(Semi-)analytical solution of Luikov equations for time-periodic boundary conditions Pecenko R, Challamel N, Colinart T, Picandet V
543 - 551	Liquid film thicknesses of oscillating slug flows in a capillary tube Youn YJ, Han Y, Shikazono N
552 - 563	Mathematical model for thermal behavior of lithium ion battery pack under overcharge Qi C, Zhu YL, Gao F, Yang K, Jiao QJ
564 - 575	Direct simultaneous reconstruction for temperature and concentration profiles of soot and metal-oxide nanoparticles in nanofluid fuel flames by a CCD camera Liu GN, Liu D
576 - 585	Modeling film boiling within chimney-structured porous media and heat pipes Yeo DY, No HC
586 - 614	Review on the measurement and calculation of frost characteristics Song MJ, Dang CB
615 - 628	A finite volume method to solve the frost growth using dynamic meshes Bartrons E, Oliet C, Gutierrez E, Naseri A, Perez-Segarra CD
629 - 638	Experimental investigation on the thermal performance of a series loop with uniform temperature Chen H, Li Q
639 - 645	Impact of different infusion rates on mass diffusion and treatment temperature field during magnetic hyperthermia Tang YD, Jin T, Flesch RCC
646 - 654	Forced convective condensation flow and heat transfer characteristics of hydrocarbon mixtures refrigerant in helically coiled tubes Yu JW, Jiang YQ, Cai WH, Li FZ
655 - 662	Tribological behaviour of the steel/bronze friction pair (journal bearing type) functioning with selective mass transfer Ilie F
663 - 676	Accelerated melting of PCM in energy storage systems via novel configuration of fins in the triplex-tube heat exchanger Mandi JM, Lohrasbi S, Ganji DD, Nsofor EC
677 - 692	Numerical simulation on a thermal management system for a small data center Zhou CL, Yang CX, Wang C, Zhang XJ
693 - 705	Characterization of unsaturated diffusivity of tight sandstones using neutron radiography Zhao YX, Xue SB, Han SB, He LF, Chen ZW
706 - 714	Shape effects of MoS2 nanoparticles on rotating flow of nanofluid along a stretching surface with variable thermal conductivity: A Galerkin approach Hamid M, Usman M, Zubair T, Ul Haq R, Wang W
715 - 725	Translational and rotational motions of small solid particles in a spatially developing turbulent boundary layer with heat transfer Li D, Luo K, Fan JR
726 - 741	Effects of electric field on flow boiling heat transfer in a vertical minichannel heat sink Feng ZF, Luo XP, Zhang JX, Xiao J, Yuan W
742 - 751	Experimental investigation of thermal conductivity of nanofluids containing of hybrid nanoparticles suspended in binary base fluids and propose a new correlation Kakavandi A, Akbari M
752 - 760	Thermal performance improvement based on the partial heating position of a heat sink Yoon Y, Park SJ, Kim DR, Lee KS
761 - 768	Extraction and evolution of bubbles attributes in a two-phase direct contact evaporator Xiao QT, Gao Q, Zhang J, Xu JX, Pan JX, Wang H
769 - 781	The effect of lateral thermal coupling between parallel microchannels on two-phase flow distribution Van Oevelen T, Weibel JA, Garimella SV
782 - 793	Development and validation of a semi-empirical model for two-phase heat transfer from arrays of impinging jets Mira-Hernandez C, Clark MD, Weibel JA, Garimella SV
794 - 799	Close-contact melting heat transfer on a heated horizontal plate: Revisited in the presence of nano-enhanced phase change materials (NePCM) Hu N, Zhu ZQ, Li ZR, Tu J, Fan LW
800 - 815	Vortex generators for active thermal management in lithium-ion battery systems Mondal B, Lopez CF, Verma A, Mukherjee PP
816 - 828	Determination of condensation heat transfer inside a horizontal smooth tube Rabiee R, Desilets M, Proulx P, Ariana M, Julien M
829 - 840	A comparative study of flow boiling HFE-7100 in silicon nanowire and plainwall microchannels Alam T, Li WM, Chang W, Yang FH, Khan J, Li C
841 - 859	Numerical simulation of entropy generation due to unsteady natural convection in a semi-annular enclosure filled with nanofluid Bezi S, Souayeh B, Ben-Cheikh N, Ben-Beya B
860 - 875	Mixed convection characteristic in a lid-driven cavity containing heated triangular block: Effect of location and size of block Gangawane KM, Oztop HF, Abu-Hamdeh N
876 - 883	Experimental observation of the maximum bubble diameter in non-stationary temperature field of subcooled boiling water flow Levin AA, Khan PV
884 - 884	Influence of the aligned flow obstacles on critical heat flux in two-phase boundary layer flow under a low flow condition (vol 121, pg 1234, 2018) Jeong U, Son HH, Kim SJ
885 - 899	Laminar mixed convection of power-law fluids in cylindrical enclosures with heated rotating top wall Turan O, Yigit S, Liang RB, Chakraborty N
900 - 911	Simulations on the cavitating flow and corresponding risk of erosion in diesel injector nozzles with double array holes Zhang L, He ZX, Guan W, Wang Q, Som S
912 - 919	Drop formation from a capillary tube: Comparison of different bulk fluid on Newtonian drops and formation of Newtonian and non-Newtonian drops in air using image processing Nazari A, Derakhshi AZ, Nazari A, Firoozabadi B
920 - 928	Flow structure and heat transfer of a sweeping jet impinging on a flat wall Park T, Kara K, Kim D
929 - 942	Flow behaviour of drop and jet modes of a laminar falling film on horizontal tubes Ding HB, Xie P, Ingham D, Ma L, Pourkashanian M
943 - 952	3D numerical study of the liquid film distribution on the surface of a horizontal-tube falling-film evaporator Qiu QG, Zhang XC, Quan SL, Zhu XJ, Shen SQ
953 - 966	Prediction and optimization of condensation heat transfer coefficients and pressure drops of R134a inside an inclined smooth tube Abadi SMANR, Mehrabi M, Meyer JP
967 - 979	Heat and mass transfer in a rarefied gas confined between its two parallel condensed phases Polikarpov AP, Graur IA
980 - 989	Nanofluid turbulent convective flow in a circular duct with helical turbulators considering CuO nanoparticles Sheikholeslami M, Jafaryar M, Li ZX
990 - 1002	Numerical investigations on the melting process of the nuclear fuel rod in RIAs and LOCAs Tang JN, Huang M, Zhao YY, Maqsood S, Ouyang XP
1003 - 1010	Numerical investigation of jet impingement cooling of a low thermal conductivity plate by supercritical pressure carbon dioxide Chen K, Xu RN, Jiang PX
1011 - 1014	Theoretical analysis of thermal damages in skin tissue induced by intense moving heat source Hobiny AD, Abbas IA
1015 - 1024	Experimental, numerical and analytic study of unconstrained melting in a vertical cylinder with a focus on mushy region effects Pan CJ, Charles J, Vermaak N, Romero C, Neti S, Zheng Y, Chen CH, Bonner R
1025 - 1032	How supercooled superhydrophobic surfaces affect dynamic behaviors of impacting water droplets? Ding B, Wang H, Zhu X, Chen R, Liao Q
1033 - 1044	Continuum-scale modeling of superheated steam drying of cellular plant porous media Le KH, Tsotsas E, Kharaghani A
1045 - 1058	A generalized Characteristic-Based Split projection method for Navier-Stokes with real fluids Cook CR, Balachandar S, Chung JN, Vu-Quoc L
1059 - 1067	Variation of the thermal conductivity of a silty clay during a freezing-thawing process Zhang MY, Lu JG, Lai YM, Zhang XY
1068 - 1075	Experimental investigation on the effect of turbulent intensity on heat transfer in a square rotating channel You RQ, Li HW, Tao Z
1076 - 1087	Transpiration cooling for additive manufactured porous plates with partition walls Huang G, Min Z, Yang L, Jiang PX, Chyu M
1088 - 1096	Prediction of oscillatory heat transfer coefficient for a thermoacoustic heat exchanger through artificial neural network technique Rahman AA, Zhang XQ
1097 - 1106	Numerical analysis for irreversible processes in a piston-cylinder system Yusof SNA, Asako Y, Faghri M, Tan LK, Sidik NAB
1107 - 1116	Exact solution of thermal response in a three-dimensional living bio-tissue subjected to a scanning laser beam Ma JX, Yang XF, Liu SB, Sun YX, Yang JL
1117 - 1135	Volumetric mass transfer coefficient, power input and gas hold-up in viscous liquid in mechanically agitated fermenters. Measurements and scale-up Petricek R, Moucha T, Rejl FJ, Valenz L, Haidl J, Cmelikova T
1136 - 1146	Heat transfer characteristics of external ventilated path in compact high-voltage motor Xu YM, Jia YJ, Ai MM, Wang YD
1147 - 1155	An optimization strategy for the inverse solution of a convection heat transfer problem Bangian-Tabrizi A, Jaluria Y
1156 - 1162	Numerical study with OpenFOAM on heat conduction problems in heterogeneous media Zhang K, Wang CA, Tan JY
1163 - 1171	Measurement of the vapor layer under a dynamic Leidenfrost drop Lee GC, Noh H, Kwak HJ, Kim TK, Park HS, Fezzaa K, Kim MH
1172 - 1180	Effects of the number of turns and the inclination angle on the operating limit of micro pulsating heat pipes Lee J, Joo Y, Kim SJ
1181 - 1197	Direct numerical simulation of strongly heated air flows in a vertical pipe using a thermophysical property table Zhao PH, Liu JM, Ge ZH, Li YJ, Zhao N, Wan YX
1198 - 1211	Analysis of heat and resistance performance of plate fin-and-tube heat exchanger with rectangle-winglet vortex generator Qian ZQ, Wang Q, Cheng JL
1212 - 1216	Local thermal non-equilibrium in porous media with heat conduction Gandomkar A, Gray KE
1217 - 1229	Numerical and experimental studies of natural convection in a heated cavity with a horizontal fin on a hot sidewall Chen HT, Lin MC, Chang JR
1230 - 1244	Influence of wet-particle deposition on air-side heat transfer and pressure drop of fin-and-tube heat exchangers Zhan FL, Zhuang DW, Ding GL, Ju PL, Tang JJ
1245 - 1261	Comparative study of vertical and horizontal indirect evaporative cooling heat recovery exchangers Li WY, Li YC, Zeng LY, Lu J
1262 - 1274	Numerical investigation of air entrapment in a molten droplet impacting and solidifying on a cold smooth substrate by 3D lattice Boltzmann method Xiong W, Cheng P
1275 - 1284	Conjugate heat transfer in the PCM-based heat storage system with finned copper profile: Application in electronics cooling Bondareva NS, Sheremet MA
1285 - 1309	Influence of height ratio on flow and heat transfer around trapezoidal geometry (a generic sharp-edged body) covering transition to periodic flow Parveez M, Dhiman AK, Harmain GA
1310 - 1320	Thermodynamic analyses and optimizations of extraction process of CO2 from acidic seawater by using hollow fiber membrane contactor Chen LG, Wang C, Xia SJ, Sun FR
1321 - 1333	Numerical and experimental investigation of flue gases heat recovery via condensing heat exchanger Machackova A, Kocich R, Bojko M, Kuncicka L, Polko K
1334 - 1346	Ammonium alum hydrate slurries with surfactants and polyvinyl alcohol as a latent heat transportation material for high temperature Hidema R, Tano T, Sato H, Komoda Y, Suzuki H
1347 - 1360	Heat transfer and fluid flow behaviors in a tube with modified wire coils Hong YX, Du J, Wang SF, Huang SM, Ye WB
1361 - 1369	Experimental investigation of heat transfer and friction factor of TiO2-SiO2 nanofluids in water:ethylene glycol mixture Nabil MF, Azmi WH, Hamid KA, Mamat R
1370 - 1370	Flow regime transition criteria for upward two-phase flow in vertical rod bndles (vol 108, pg 423, 2017) Liu H, Hibiki T