Powder Technology

Powder Technology, Vol.228 Entire volume, number list

ISSN: 0032-5910 (Print)

In this Issue (57 articles)

1 - 13	Experimental and numerical investigation of solid behavior in a gas-solid turbulent fluidized bed Gao X, Wu C, Cheng YW, Wang LJ, Li X
14 - 17	Master debinding curves for solvent extraction of binders in powder injection molding Enneti RK, Shivashankar TS, Park SJ, German RM, Atre SV
18 - 25	Comparison of silver and palladium nanoparticles loaded on activated carbon for efficient removal of Methylene blue: Kinetic and isotherm study of removal process Ghaedi M, Heidarpour S, Kokhdan SN, Sahraie R, Daneshfar A, Brazesh B
26 - 35	Modeling the influence of a process control agent on the properties of metal matrix composite powders using artificial neural networks Canakci A, Ozsahin S, Varol T
36 - 46	Application of iron-based powders in tungsten inert gas welding for 17Cr-10Ni-2Mo alloys Tseng KH, Chuang KJ
47 - 55	Preparation and characterization of vitexin powder micronized by a supercritical antisolvent (SAS) process Zu YG, Zhang Q, Zhao XH, Wang D, Li W, Sui XY, Zhang Y, Jiang SG, Wang QX, Gu CB
56 - 68	Computational fluid dynamics of riser using kinetic theory of rough spheres Wang S, Liu GD, Lu HL, Yang YC, Xu PF, Sun LY
69 - 83	Comparison of phenomenological and fundamental modelling approaches for predicting fluidized bed reactor performance Cloete S, Zaabout A, Johansen ST, Amini S
84 - 90	Production of polymer particles below 5 mu m by wet grinding Schmidt J, Plata M, Troger S, Peukert W
91 - 99	Precipitation kinetics of PMMA-co-BMA sub-micrometric particles with compressed CO2 assisted-atomization process Wu HT, Yang MW
100 - 107	The effect of operating conditions on resistance parameters of filter media and limestone dust cake for uniformly loaded needle felts in a pilot scale test facility at ambient conditions Saleem M, Krammer G, Tahir MS
108 - 114	The formation of deposit in a magnetic fluid: Numerical and experimental study Balakin BV, Notoy I, Hoffmann AC, Kosinski P
115 - 120	Increasing biochar surface area: Optimization of ball milling parameters Peterson SC, Jackson MA, Kim S, Palmquist DE
121 - 127	An experimental study of the influence of temperature on char separation in a moving granular bed Yang SI, Chung IL, Wu SR
128 - 130	Green synthesis of CuO nanoflakes from CuCO3 center dot Cu(OH)(2) powder and H2O2 aqueous solution Wang TX, Xu SH, Yang FX
131 - 140	Gas-solid structure in the vicinity of a sparger nozzle in a fluidized bed Sauriol P, Cui HP, Chaouki J
141 - 148	Characterization of titanium powder: Microscopic views and macroscopic flow Pohlman NA, Roberts JA, Gonser MJ
149 - 157	Predicting granule size distribution of a fluidized bed spray granulation process by regime based PLS modeling of acoustic emission data Poutiainen S, Matero S, Hamalainen T, Leskinen J, Ketolainen J, Jarvinen K
158 - 162	Gas phase synthesis of Ni3Fe nanoparticles by magnesium reduction of metal chlorides Mirhoseini F, Bateni A, Firoozi S
163 - 170	Synthesis of silver nano catalyst by gel-casting using response surface methodology Ahmadi S, Manteghian M, Kazemian H, Rohani S, Darian JT
171 - 186	Comparative study by PEPT and DEM for flow and mixing in a ploughshare mixer Laurent BFC, Cleary PW
187 - 192	Sphericizing tungsten particles by means of localized preferential oxidation and alkaline washing Qiu WT, Li Z, Xiao Z, Gong S, Lei Q
193 - 198	Some computational considerations associated with discrete element modeling of cylindrical particles Guo Y, Wassgren C, Ketterhagen W, Hancock B, Curtis J
199 - 205	Low temperature powder injection molding of iron micro-nano powder mixture You WK, Choi JP, Yoon SM, Lee JS
206 - 209	Adaptability verification of scaling law to solid mixing and segregation behavior in bubbling fluidized bed Zhang JW, Gao W, Zhao ZG, Liu ZH, Narukawa M, Suda T, Xu GW
210 - 218	Fe and Ni co-doped TiO2 nanoparticles prepared by alcohol-thermal method: Application in hydrogen evolution by water splitting under visible light irradiation Sun T, Fan J, Liu EZ, Liu LS, Wang Y, Dai HZ, Yang YH, Hou WQ, Hu XY, Jiang ZY
219 - 227	Study on the gas-solid flow and heat transfer characteristics of evaporating recycle valve Ji XY, Lu XF, He HH, Lu JY, Wang QH, Kang YH, Yan LY
228 - 230	Synthesis and characterization of bismuth molybdate nanoparticles within nanoreactors of reverse micelles Masteri-Farahani M, Hosseini HS
231 - 240	Preparation and characterization of nanocrystalline titania powders by sonochemical synthesis Duvarci OC, Ciftcioglu M
241 - 249	Effect of poly-dispersity on the stability of agglomerates subjected to simple fluid strain fields Shrimpton JS, Danby M
250 - 253	Mechanochemical synthesis of Fe3O4@(Mg-Al-OH LDH) magnetic composite Zhang FR, Du N, Zhang RJ, Hou WG
254 - 257	Highly dense steel components prepared by magnetic pulsed compaction of iron-based powders Lee JG, Lim CH, Kim HS, Hong SJ, Kim MT, Kang BC, Park DK, Lee MK, Rhee CK
258 - 263	Efficient visible-light-induced photocatalytic activity over the novel Ti-doped BiOBr microspheres Wang RJ, Jiang GH, Wang XH, Hu RB, Xi XG, Bao SY, Zhou Y, Tong T, Wang S, Wang T, Chen WX
264 - 271	Generalized flow regime diagram of fluidized beds based on the height to bed diameter ratio Shaul S, Rabinovich E, Kalman H
272 - 276	Characterization of agglomeration state in nanocrystalline 3YSZ powders through pressure-displacement curves and nanoindentation of green compacts Patil SB, Bhargava P
277 - 283	Facile synthesis of TiO2:Eu3+ spindle shaped nanoparticles from titanate nanobelt precursors Li HB, Zheng KY, Xu XC, Zhao H, Song YH, Sheng Y, Huo QS, Zou HF
284 - 294	Shape and size effects on the packing density of binary spherocylinders Meng LY, Lu P, Li SX, Zhao J, Li T
295 - 300	Spark plasma sintering of fine Mg2Si particles Savary E, Gascoin F, Marinel S, Heuguet R
301 - 308	Spray roasting of iron chloride FeCl2: laboratory scale experiments and a model for numerical simulation Schiemann M, Wirtz S, Scherer V, Barhold F
309 - 318	CFD-DEM simulation of particle transport and deposition in pulmonary airway Chen XL, Zhong WQ, Zhou XG, Jin BS, Sun BB
319 - 323	Improvements of calcium oxide based sorbents for multiple CO2 capture cycles Vieille L, Govin A, Grosseau P
324 - 326	Flotation of oxidized coal dry-ground with collector Xia WC, Yang JG, Zhu B
327 - 333	Formation of slot cut for creating free face in solid limestone bench: A case study Rai P, Yang HS, Choudhary BS
334 - 338	Microstructure, mechanical properties and sintering model of B4C nozzle with micro holes by powder injection molding Wang CR, Lu Z, Zhang KF
339 - 348	Aspects of foam stability influencing foam granulation in a twin screw extruder Thompson MR, Mu B, Sheskey PJ
349 - 358	Characterization of the internal morphology of agglomerates produced in a spray fluidized bed by X-ray tomography Dadkhah M, Peglow M, Tsotsas E
359 - 370	Incipient flow properties of two-component fine powder systems and their relationships with bulk density and particle contacts Kojima T, Elliott JA
371 - 376	Synthesis of novel Mn3O4 microsphere and its distinctive capacitance change during electrochemical cycling Guo SH, Zhang M, Zhang GN, Zheng L, Kang LP, Liu ZH
377 - 384	Fabrication of zinc coatings on alumina balls from zinc powder by mechanical coating technique and the process analysis Hao L, Lu Y, Sato H, Asanuma H
385 - 394	Particle attrition with supersonic nozzles in a fluidized bed at high temperature Li F, Briens C, Berruti F, McMillan J
395 - 403	Method for characterization of loss-in-weight feeder equipment Engisch WE, Muzzio FJ
404 - 409	Investigation of structural, microstructural and magnetic properties of mechanically alloyed amorphous/nanocrystalline Fe32.5Co32.5Nb35 powders Nasibi S, Shokrollahi H, Karimi L, Janghorban K
410 - 415	Multifunctional properties of hydroxyapatite/titania bio-nano-composites: bioactivity and antimicrobial studies Nathanael AJ, Lee JH, Mangalaraj D, Hong SI, Rhee YH
416 - 423	A review of the Residence Time Distribution (RTD) applications in solid unit operations Gao YJ, Muzzio FJ, Ierapetritou MG
424 - 428	Deformed liquid marbles: Freezing drop oscillations with powders Marston JO, Zhu Y, Vakarelski IU, Thoroddsen ST
429 - 434	Frictional behaviour of CaCO3 powder compacts Berg S, Marklund P, Haggblad HA, Jonsen P
435 - 442	Influence of particle size ratio on densification behaviour of AISI H13/AISI M3:2 powder mixture Fedrizzi A, Pellizzari M, Zadra M